SN/T 3735-2013Test method of classification for dangerous goods. Isothermal storage (English PDF)
危险品分类试验方法 等温储存
This is a limited preview
Buy now to download the full PDF (8 pages)
Need quotation for your management?
Get a formal quotation for SN/T 3735-2013 in 30 minutes.
Issued by
General Administration of Customs
Level / Type
National · Recommended
Issue date
November 6, 2013
Implementation date
June 1, 2014
Scope
SN/T 3735-2013 is the English-translated version of 危险品分类试验方法 等温储存.
SN/T 3735-2013 - This standard specifies the classification of dangerous goods, such as testing temperature storage test methods.
This standard applies to the classification of dangerous goods Isothermal storage test for determining the reaction mass, material decomposition at a constant temperature with time-dependent heat Rate and determine material packed in containers for transport SADT.
Found what you need?
Document preview — SN/T 3735-2013
National Standard of the People's Republic of China
- ICS
- 13.300
- Classification
- A80
Issued by: General Administration of Customs
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Equipment and Materials
Foreword
This standard was drafted in accordance with GB/T 1.1-2009 given rules.
This standard and the United Nations "on the Recommendations on the Transport of Dangerous Goods Model Regulations" (Rev. 17) and the United Nations "Dangerous Goods Recommendations on the Transport of Tests and Criteria Handbook "(5th revised edition) of the non-equivalent, its technical content above manual Ends Full agreement on a standard text format according to GB/T 1.1-2009 made editorial changes.
This standard is proposed and managed by the National Certification and Accreditation Administration Committee.
This standard was drafted. Tianjin People's Republic of China Exit Inspection and Quarantine, Hunan People's Republic of China Entry-Exit Inspection and Quarantine Bureau.
1 Scope
This standard specifies the classification of dangerous goods, such as testing temperature storage test methods.
This standard applies to the classification of dangerous goods Isothermal storage test for determining the reaction mass, material decomposition at a constant temperature with time-dependent heat Rate and determine material packed in containers for transport SADT.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
About Recommendations on the Transport of Dangerous Goods Model Regulations (UN, 17th Revision) Transport of Dangerous Goods Recommendations Manual of Tests and Criteria (UN, 5th Revised Edition)
3 Terms and Definitions
"On Recommendations on the Transport of Dangerous Goods Model Regulations", "on the Transport of Dangerous Goods Manual of Tests and Criteria Recommendations" is defined the following terms and definitions apply to this document.
Critical ambient temperature as packaged material does not show the highest temperature self-accelerating decomposition.
SADT self-acceleratingdecompositiontemperature Material mounted to occur within a transport container lowest self-accelerating decomposition temperature, that is the critical ambient temperature rounded to the next higher the 5 °C multiples.
Isothermal storage the reaction or decomposition products stored at a constant temperature.
4 Equipment and Materials
Warning. this test with a potential explosion hazard, test equipment shall comply with the relevant safety requirements.
4.1 air-insulated heat sink (aluminum block), the method of controlling the heating to keep a constant temperature.
4.2 cryostat, keeping the temperature below 40 °C.
4.3 heating controller, temperature control accuracy of ± 0.2 °C.
4.4 platinum resistance.
4.5 sample container, the volume of 70cm3, respectively, for samples containing inert substances, testing diagram shown in A.1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.
How to Download SN/T 3735-2013
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
SN/T 2378.1-2026 — Rules for the inspection of imported natural gas - Part 1: Pipeline inspection
SN/T 5778-2026 — Rules for the inspection of common imported and exported rare earth products
SN/T 5784-2026 — Inspection of casting and forging production processes of steel - Hot acid etching method
SN/T 3735-2013
$165.00