QC/T 883-2011Sealing plugs (English PDF)
密封塞
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for QC/T 883-2011 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
December 20, 2011
Implementation date
July 1, 2012
Scope
QC/T 883-2011 is the English-translated version of 密封塞.
QC/T 883-2011 is the recommended Chinese automotive industry standard for sealing plugs. It gives the types and sizes of the plug and the technical conditions it has to meet.
The plugs it covers close holes of 4 mm to 20 mm diameter at sealing pressures of no more than 20 MPa, and serve the air and hydraulic systems of motor vehicles; the bodies they are fitted into may be aluminium, cast iron or steel.
Its Chinese classification is T33 and its international classification 43.040. GB/T 90.1, GB/T 90.2, GB/T 699, GB/T 3190, QC/T 326 and QC/T 625 are cited alongside it. Issued on 20 December 2011, it has applied since 1 July 2012.
Found what you need?
Document preview — QC/T 883-2011
National Standard of the People's Republic of China
- ICS
- 43.040
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- [Preview only]
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 3.2 Abbreviations
- 4 Technical requirements
- 5 Test Methods
- 5.1 Protocol stack
- 5.2 Node state
- 5.3 Transmission rate
- 5.4 Connectivity
- 5.5 Bit error rate
- 5.6 Wiring harness fault diagnosis
- 5.7 Electrical indexes
- 6 Inspection Rules
- 6.1 Test environment
- 7 Signs, documents, packaging, transportation and storage
- 8 Inspection report
- 9 Marks, packaging
1 Foreword
QC/T 883-2011 was issued by Ministry of Industry and Information Technology of the People's Republic of China on 20 December 2011 and has been in force since 1 July 2012.
The QC/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.
The document runs to 15 pages in English translation.
2 Scope Preview
This standard is the recommended Chinese automotive industry standard for sealing plugs. It gives the types and sizes of the plug and the technical conditions it has to meet. The plugs it covers close holes of 4 mm to 20 mm diameter at sealing pressures of no more than 20 MPa, and serve the air and hydraulic systems of motor vehicles; the bodies they are fitted into may be aluminium, cast iron or steel. Its Chinese classification is T33 and its international classification 43.040. GB/T 90.1, GB/T 90.2, GB/T 699, GB/T 3190, QC/T 326 and QC/T 625 are cited alongside it.
QC/T 883-2011 falls under ICS 43.040, in the field of road vehicle engineering.
This catalogue holds 396 other QC/T standards in that field.
In this catalogue, QC/T standards carry edition years from 1991 to 2026.
3 Normative references
GB/T 90.1
GB/T 90.2
GB/T 699
GB/T 3190
QC/T 326
QC/T 625
4 About this standard
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
English translation: about 15 pages
5 Related standards
Standards on related subjects:
QC/T 606-2022 — Clips - Type H
QC/T 929-2022 — Plastic cable and tubing clips with side fixing hole
QC/T 928-2022 — Plastic cable and tubing clips with middle fixing hole
QC/T 715-2026 — Test method for friction coefficient of threaded fasteners for automobiles
QC/T 620-2023 — Clamps with worm gear driver type A
QC/T 598-2022 — Projection weld bolts on the bearing face
6 Classification and status
International classification (ICS): 43.040
Chinese Standard Classification (CCS): T 31
Prefix QC/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 90.1Fasteners - Acceptance inspection
- GB/T 90.2Fasteners--Marking and packaging
- GB/T 699Quality carbon structure steels
- GB/T 3190Chemical composition of wrought aluminium and aluminium alloys
- QC/T 326Numbering rules for automotive standardized parts
- QC/T 625Metallic coatings and chemical conversion coatings for automobiles
Similar standards
How to Download QC/T 883-2011
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 3190-1996 — Wrought aluminium and aluminium alloys--Chemical composition limits
GB/T 3190-2008 — Wrought aluminium and aluminium alloy - Chemical composition
GB/T 3190-2020 — Chemical composition of wrought aluminium and aluminium alloys
QC/T 883-2011
$85.00