QC/T 459-2004Trucks with loader cranes (English PDF)
随车起重运输车
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for QC/T 459-2004 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
February 10, 2004
Implementation date
August 1, 2004
Scope
QC/T 459-2004 is the English-translated version of 随车起重运输车.
QC/T 459-2004 is the Chinese standard "Trucks with loader cranes". Its scope clause reads: This standard specifies the definitions, requirements, test methods, inspection rules, marking, instructions for use, accompanying documents, transportation and storage concerning trucks with loading crane.
This standard is applicable to a truck with loading crane modified from a finalized goods vehicle or a finalized stereotyped automobile chassis (hereinafter referred to as "lift trucks"). Its clauses include definitions.
Found what you need?
Document preview — QC/T 459-2004
National Standard of the People's Republic of China
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- Foreword I
- 1 Scope
- 2 Normative references
- 3 Definitions
- 4 Requirements
- 5 Test methods
- 6 Inspection rules
- 7 Marking and instructions for use
- 8 Accompanying documents, transportation and storage
- Annex A (Normative) Stress measurement criteria
- Annex B (Normative) Table of calculated load
- Annex C (Informative) Overturning line reference diagrams
- Annex D (Informative) Test record tables
1 Scope
This standard specifies the definitions, requirements, test methods, inspection rules, marking, instructions for use, accompanying documents, transportation and storage concerning trucks with loading crane.
This standard is applicable to a truck with loading crane modified from a finalized goods vehicle or a finalized stereotyped automobile chassis (hereinafter referred to as "lift trucks").
2 Normative references
The following normative documents contain provisions which, through reference in this standard, constitute provisions of this standard. For dated references, subsequent amendments (excluding corrections) to, or revisions, of any of these publications do not apply to this standard. However, parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the normative documents indicated below. For undated references, the latest edition applies.
GB/T 3766 Hydraulic fluid power - General rules relating to systems
GB/T 3811 Design rules for cranes
GB/T 9969.1 General principles for preparation of instructions for use of industrial products
GB/T 12534 Motor vehicles - General rules of road test method
GB 15052 Lifting appliances - Dangerous positions and signs
GB/T 18411 Road vehicles manufacturer’s plate
JB/T 5943 Construction machinery - General specifications for welding parts
QC/T 252 Special purpose vehicles - Engineering approval evaluation program
QC/T 484 Automobiles - Paint coating
QC/T 29104 Limiting value of contamination level of solid particles of special purpose vehicle hydraulic system
QC/T 29105 Test method for contamination level of solid particles of special purpose vehicle hydraulic system
3 Definitions
For the purposes of this standard, the following definitions apply.
3.1 maximum hoisting moment
maximum value of the product of the rated lifting load and the corresponding operating range ability
3.2 rated lifting load
maximum total mass (including the mass of the lifting appliance) of the objects allowed to be lifted for safe operation during different operating range abilities
3.3 maximum lifting load
maximum total mass of the objects allowed to be lifted by a lift truck during minimum operating range ability
3.4 range ability
horizontal distance from the vertical line of the hook center of the lift truck to the slewing centerline
3.5 minimum operating range ability
minimum horizontal distance from the vertical line of the hook center to the slewing centerline when the lift truck can operate effectively
3.6 maximum operating range ability
maximum horizontal distance from the vertical line of the hook center to the slewing centerline when the lift truck has the maximum arm length and the boom is in a horizontal state
3.7 maximum lifting height
vertical distance from the hook center to the ground plane where the lift truck is located when the hook is at the upper limit position under the operating conditions of maximum arm length, maximum elevation angle, full extension of vertical stabilizer oil cylinder and complete vehicle unladen mass […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download QC/T 459-2004
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
QC/T 1005-2026 — Performance requirements and bench test methods for hydraulic solenoid valve assembly of electronic stability control system and antilock brake system of automoive
QC/T 1022-2026 — Technical specifications and test methods of reduction gearbox for battery electric vehicles
QC/T 1041-2026 — Control system of fuel evaporative pollutants from Motorcycles with petrol engine
QC/T 459-2004
$225.00