QC/T 294-1999Technical specifications for automotive axle shafts (English PDF)
汽车半轴技术条件
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for QC/T 294-1999 in 30 minutes.
Issued by
MIIT
Level / Type
Industry · Recommended
Issue date
January 1, 1999
Implementation date
January 1, 1999
Scope
QC/T 294-1999 is the English-translated version of 汽车半轴技术条件.
Automotive axle shafts are the subject of QC/T 294-1999, a recommended standard of the Chinese automobile industry. It sets the technical requirements for the shaft, the test methods, the inspection rules and the requirements for marking, packaging, transport and storage.
Its scope is the full-floating and semi-floating axle shafts of non-steering drive axles with a rated axle load of 13 t or less, fitted to vehicles other than mining trucks.
It is classified T21 in the Chinese system, among the standards for the driveline of a vehicle. The standard replaced ZB T21004-1989 and quotes QC/T 293. It was issued on 1 January 1999.
Found what you need?
Document preview — QC/T 294-1999
National Standard of the People's Republic of China
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
Contents
- [Preview only]
- 1 Scope
- 1.1 Brake performance
- 1.2 Heat fade and recovery of brake
- 1.3 Line failure and booster failure
- 1.4 Wear of brake linings (pads)
- 2 Normative references
- 3 Terms and definitions
- 3.2 Abbreviations
- 4 Technical requirements
- 4.1 Arrangement form
- 5 Test Methods
- 5.1 Protocol stack
- 5.2 Node state
- 5.3 Transmission rate
- 5.4 Connectivity
- 5.5 Bit error rate
- 5.6 Wiring harness fault diagnosis
- 5.7 Electrical indexes
- 6 Inspection Rules
- 6.1 Test environment
- 7 Signs, documents, packaging, transportation and storage
- 8 Inspection report
- 9 Marks, packaging
1 Foreword
QC/T 294-1999 is issued by Ministry of Industry and Information Technology of the People's Republic of China.
The QC/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.
The document runs to 15 pages in English translation.
2 Scope Preview
Automotive axle shafts are the subject of QC/T 294-1999, a recommended standard of the Chinese automobile industry. It sets the technical requirements for the shaft, the test methods, the inspection rules and the requirements for marking, packaging, transport and storage. Its scope is the full-floating and semi-floating axle shafts of non-steering drive axles with a rated axle load of 13 t or less, fitted to vehicles other than mining trucks. It is classified T21 in the Chinese system, among the standards for the driveline of a vehicle. The standard replaced ZB T21004-1989 and quotes QC/T 293. It was issued on 1 January 1999.
QC/T 294-1999 carries no ICS number and no Chinese Standard Classification code.
This catalogue holds 1,601 other QC/T standards.
Of the 409 QC/T standards that do carry an ICS number, 397 (97%) fall under ICS 43, in the field of road vehicle engineering.
3 Normative references
QC/T 293
4 About this standard
Issued by: Ministry of Industry and Information Technology of the People's Republic of China
English translation: about 15 pages
5 Classification and status
Prefix QC/T: recommended standard.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Normative references
Similar standards
How to Download QC/T 294-1999
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
QC/T 293-1999 — Bench test methods for automotive axle shafts
QC/T 293-2019 — Specifications and bench test methods for automotive axle shafts
QC/T 1005-2026 — Performance requirements and bench test methods for hydraulic solenoid valve assembly of electronic stability control system and antilock brake system of automoive
QC/T 294-1999
$219.00