Valid

QB 2585-2007[QB/T 2585-2007] Hydromassage bathtub (English PDF)

Preview PDF

Also coversQB2585-2007

This is a limited preview

Buy now to download the full PDF (11 pages)

Need quotation for your management?

Get a formal quotation for QB 2585-2007 in 30 minutes.

Issued by

National Development and Reform Commission of PRC

Level / Type

National · Mandatory

Issue date

May 29, 2007

Implementation date

December 1, 2007

Scope

QB 2585-2007 ([QB/T 2585-2007] Hydromassage bathtub) is available as an English-translated PDF.

QB 2585-2007 — This standard specifies the definition, requirements, test methods, inspection rules and signs, instruction manuals, packaging, transportation and storage of hydromassage bathtubs (hereinafter referred to as "hydromassage bathtubs").

This standard applies to hydromassage bathtub used by no more than three persons assembled from bathtubs, water pumps, air pumps, nozzles, drains and other accessories.

Found what you need?

Document preview — QB 2585-2007

National Standard of the People's Republic of China

ICS: 91.140.70

Issued by: National Development and Reform Commission of PRC

Foreword...3
1 Scope...5
2 Normative references...5
3 Definitions...5
4 Requirements...6
5 Test methods...8
6 Inspection rules...10
7 Markings, instruction manuals, packaging, transportation, storage...11

Foreword

Clause 4.1.2, 4.4.3, 4.5, and 4.6 of this standard are mandatory, and the

rest are recommended.

This standard is an amendment to QB 2585-2003 "Hydromassage bathtub".

In order to better meet the needs of domestic and foreign markets and to align

product quality with international standards, in the revision process of this

standard, combined with the development status of China's sanitary hardware

industry, it mainly refers to the United States UL1795 "Whirlpool bathtub", the

European standard EN 60335-2-60-2003 "Household and similar purpose

appliance safety - Special requirements for vortex bathtub", EN 12764 "Vortex

bathtub" and other advanced foreign standards.

As compared with QB 2585-2003, the main changes of this standard are as

follows.

- MODIFY the product's water jet distance requirements;

- MODIFY the requirements for product retention water;

- MODIFY the provisions for product noise values;

- ADD the requirements that the product shall be equipped with a backflow

device that isolates the sewer odor.

This standard was proposed by China Light Industry Federation.

This standard shall be under the jurisdiction of the National Hardware Products

Standardization Technical Committee Construction Hardware Subcommittee.

Drafting organizations of this standard. Oulusha Co., Ltd., Apollo (China) Co.,

Ltd., Hangzhou Flett Plastics Development Co., Ltd., Foshan Quality

Measurement Supervision and Inspection Center, Zhongshan Sally Sanitary

Ware Equipment Co., Ltd., Foshan Nanhai Yigao Sanitary Ware Co., Ltd.,

Foshan Huameijia Sanitary Ware Manufacturing Co., Ltd., Zhuhai Shulima

Temperature Control Sanitary Ware Co., Ltd., Ningbo Guanghe Sanitary Ware

Co., Ltd., Foshan Shunde Meijie Sanitary Ware Industry Co., Ltd., Ningbo

Aoleishi Sanitary Ware Co., Ltd., National Light Industrial Building Hardware

Quality Supervision and Inspection Center.

Main drafters of this standard. Wang Mingchang, Liu Yong, Qu Zhuokun, Gao

Jianyue, Liu Fengxiang, Li Guang, Rao Jun, Xie Qingjun, Dai Longquan, Su

Lihua, Zhang Yongquan, Qi Yaode.

Participated drafters of this standard. Jing Feng, Zeng Jiale, Gao Zhiwan,

Hydromassage bathtub

1 Scope

This standard specifies the definition, requirements, test methods, inspection

rules and signs, instruction manuals, packaging, transportation and storage of

hydromassage bathtubs (hereinafter referred to as "hydromassage bathtubs").

This standard applies to hydromassage bathtub used by no more than three

persons assembled from bathtubs, water pumps, air pumps, nozzles, drains

and other accessories.

2 Normative references

The provisions in following documents become the provisions of this standard

through reference in this standard. For the dated references, the subsequent

amendments (excluding corrections) or revisions do not apply to this standard;

however, parties who reach an agreement based on this standard are

encouraged to study if the latest versions of these documents are applicable.

For undated references, the latest edition of the referenced document applies.

GB/T 191-2000 Packaging - Pictorial marking for handling of goods

GB 4706.73-2004 Household and similar electrical appliances safety -

Particular requirements for whirlpool baths

GB 18145-2003 Ceramic cartridge faucets

JC/T 932-2003 Drainage fittings for sanitary wares

JC/T 779-2000 Glass fiber reinforced plastics baths

QB 1334-2004 Universal technical terms for faucets

QB/T 2664-2004 Enameled bathtub

3 Definitions

The hydromassage bathtub is a bathtub with a jet of air-containing water that is

injected into the body to produce a massage effect.

5 Test methods

5.1 Appearance

Appearance is tested by the visual inspection method, visual inspection shall

be carried out under diffuse light, the illumination shall not be less than 300 lx,

and 500 mm from the object under test.

5.2 Bathtub block

5.2.1 The enameled bathtub is tested in accordance with QB/T 2664-2004.

5.2.2 Glass fiber reinforced plastic bathtubs are tested in accordance with JC/T

779-2000.

5.2.3 The bathtubs of other surface materials are tested in accordance with the

corresponding standards.

5.3 Determination of surface treatment of metal fittings

5.3.1 Electroplating and spraying surface are measured in accordance with 6.4

in QB 1334-2004.

5.3.2 The corrosion resistance of electroplating and coating shall be measured

in accordance with 6.7 of QB 1334-2004.

5.4 Use performance

5.4.1 Determination of water jet distance

PLACE the bathtub on a platform, LEVEL the bathtub, INJECT water 50 mm

above the center of the highest nozzle of the bathtub, START the pump, USE

the steel ruler to measure the water jet horizontal distance.

5.4.2 Determination of tightness

5.4.2.1 INJECT the room temperature water into the hydromassage bathtub to

the overflow level, START the pump to make the running time of the circulation

system not less than 10 mm. Visually CHECK each sealing surfaces of the

hydromassage bathtub and the joints of the pipes.

5.4.2.2 INJECT the room temperature water into the hydromassage bathtub to

the overflow level, BLOCK all nozzle outlets in the bathtub, START the water

pump, visually CHECK the pipe connections of bathtub.

5.4.2.3 INJECT water at into the hydromassage bathtub to the overflow

level, START the pump to make the running time of the circulation system not

5.7 Detection of backflow device for insolation of sewer odor

REMOVE the drain cover from the product, visually CHECK the water seal in

the drain.

6 Inspection rules

Product inspection is divided into exit-factory inspection and type inspection.

6.1 Exit-factory inspection

6.1.1 Each product shall be subject to exit-factory inspection, and can only be

delivered after passing the inspection.

6.1.2 Exit-factory inspection items are as shown in Table 4.

6.2 Type inspection

In one of the following situations, a type inspection shall be carried out.

a) The trial production finalization identification of new product or trans-plant

production of old product;

b) When the product being produced has significant changes in design,

process, production equipment, management, etc. that may affect product

performance;

c) In normal production, one inspection shall be performed regularly after a

certain period of time or accumulation of a certain quantity;

d) When production resumes after production suspension;

e) When there is a big difference between the exit-factory inspection result

and the last type inspection;

f) When the national quality supervision institute proposes the requirements

for type inspection

6.2.2 The type inspection shall be carried out in accordance with all the items

required by this standard.

6.2.3 Type inspections shall be performed for the qualified product after exit-

factory inspection, one set is taken from each batch for inspection. If the

inspection fails to meet this standard, the number of samples may be doubled.

If it still does not meet this standard, the batch of products shall be judged as

disqualified.

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.

Referenced standards

Normative references

GB 4706.73-2004 · QB 1334-2004

How to Download QB 2585-2007

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.