Valid

NB/T 10187-2019Technical requirement and test method of the floating body of floating PV system (English PDF)

水上光伏系统用浮体技术要求和测试方法

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for NB/T 10187-2019 in 30 minutes.

Issued by

NEA

Level / Type

Industry · Recommended

Issue date

June 4, 2019

Implementation date

October 1, 2019

Scope

NB/T 10187-2019 is the English-translated version of 水上光伏系统用浮体技术要求和测试方法.

NB/T 10187-2019 is the Chinese standard "Technical requirement and test method of the floating body of floating PV system". Its scope clause reads: This standard specifies the environmental conditions, technical requirements, test methods, inspection items and classification of the floating body of floating PV system.

This standard is applicable to floating bodies, including materials and bolts, which are produced by using medium (high) density polyethylene as the main raw material as well as additives.

Its clauses include terms and definitions; environmental conditions; technical requirements.

Found what you need?

Document preview — NB/T 10187-2019

National Standard of the People's Republic of China

Issued by: National Energy Administration of the People's Republic of China

Contents

  • Foreword i
  • 1 Scope
  • 2 Normative references
  • 3 Terms and definitions
  • 4 Environmental conditions
  • 5 Technical requirements
  • 5.1 General
  • 5.2 Materials
  • 5.3 Floating body
  • 6 Test method
  • 6.1 Materials
  • 6.2 Floating body
  • 7 Inspection items and classification
  • 7.1 Inspection classification
  • 7.2 End-of-manufacturing inspection
  • 7.3 Type test
  • 7.4 Inspection items

1 Scope

This standard specifies the environmental conditions, technical requirements, test methods, inspection items and classification of the floating body of floating PV system.

This standard is applicable to floating bodies, including materials and bolts, which are produced by using medium (high) density polyethylene as the main raw material as well as additives.

2 Normative references

The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition (including any amendments) applies.

GB/T 1033.1-2008 Plastics—Methods for determining the density of non-cellular plastics —Part 1: Immersion method, liquid pyknometer method and titration method

GB/T 1034-2008 Plastics—Determination of water absorption

GB/T 1040.1-2006 Plastics—Determination of tensile properties—Part 1: General principles

GB/T 1040.2-2006 Plastics—Determination of tensile properties—Part 2: Test conditions for moulding and extrusion plastics

GB/T 1040.3-2006 Plastics—Determination of tensile properties—Part 3: Test conditions for films and sheets

GB/T 1043.1-2008 Plastics—Determination of charpy impact properties—Part 1: Non-instrumented impact test

GB/T 1633-2000 Plastics—Thermoplastic materials—Determination of Vicat softening temperature (VST)

GB/T 1842-2008 Plastics—Test method for environmental stress-cracking of polyethylene

GB/T 2408-2008 Plastics—Determination of burning characteristics—Horizontal and vertical test

GB/T 2411-2008 Plastics and ebonite—determination of indentation hardness by means of a durometer (shore hardness)

GB/T 2423.7 Environmental testing—Part 2: Test methods—Test Ec: Rough handling shocks, primarily for equipment-type specimens

GB/T 5465.2-2008 Graphical symbols for use on electrical equipment—Part 2: Graphical symbols

GB/T 5470-2008 Plastics—Determination of the brittleness temperature by impact

GB/T 6672-2001 Plastics film and sheeting—Determination of thickness by mechanical scanning

GB/T 9341-2008 Plastics—Determination of flexural properties

GB/T 9352-2008 Plastic—Compression moulding of test specimens of thermoplastic materials

GB/T 16422.3-2014 Plastics—Methods of exposure to laboratory light sources—Part 3: Fluorescent UV lamps

GB/T 17219-1998 Standard for safety evaluation of equipment and protective materials in drinking water system

GB/T 17643-2011 Geosynthetics—Polyethylene geomembrane

GB/T 19466.6-2009 Plastics—Differential scanning calorimetry (DSC)—Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)

GB/T 50621 Technical standard for on-site inspection of steel structures

JC/T 1050 Classification and test method of slip resistance for ground stones

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

3.1 floating body

minimum unit of floating system on the water surface for installing photovoltaic modules or supporting key equipment of photovoltaic power generation system or for other auxiliary functions

3.2 connection pin

connection between floating bodies

4 Environmental conditions

The floating body is used if a) the wave height on the water surface is not higher than 0.5m;

b) the water velocity is not higher than 0.51m/s;

c) the wind speed is not higher than 36m/s;

d) ambient temperature is -25°C~45°C;

e) snow load is not higher than 0.45kN/m2.

5 Technical requirements

5.1 General

The floating body mainly includes a main floating body and an auxiliary floating body. The main floating body generally consists of a body, connecting bolts, connection pins and component mounting members. The auxiliary floating body mainly consists of a body, connection pins and connecting bolts. The floating body used for fixing with the anchoring system shall also include the mounting member of anchoring system. Each part shall meet the relevant requirements of this standard.

5.2 Materials

5.2.1 General requirements

Recycled materials are not allowed for floating materials (recycled materials do not include flash produced in the production process). The environmental protection properties, physical properties, mechanical properties, thermal properties, weather resistance and fire resistance of floating materials shall meet the requirements of the following clauses.

5.2.2 Environmental protection properties

The floating body shall not pollute the water, and the test results shall meet the hygiene requirements of Table 1 in GB/T 17219-1998.

5.2.3 Physical properties
5.2.3.1 Material density

The density of floating material shall not be less than 0.930g/cm3.

5.2.3.2 Water absorption

The water absorption mass fraction of floating materials shall not exceed 0.1%.

5.2.3.3 Environmental stress cracking time

The environmental stress cracking time (F50) of floating materials shall not be less than 1000h.

5.2.4 Mechanical properties
5.2.4.1 Tensile properties

The tensile properties of floating materials shall meet the requirements in Table 1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

How to Download NB/T 10187-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

NB/T 10187-2019

$210.00