JTG 3362-2018Specifications for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts (English PDF)
公路钢筋混凝土及预应力混凝土桥涵设计规范
Also coversJTG3362-2018
This is a limited preview
Buy now to download the full PDF (250 pages)
Need quotation for your management?
Get a formal quotation for JTG 3362-2018 in 30 minutes.
Issued by
Ministry of Transport
Level / Type
Industry · Mandatory
Issue date
July 16, 2018
Implementation date
November 1, 2018
Scope
JTG 3362-2018 is the English-translated version of 公路钢筋混凝土及预应力混凝土桥涵设计规范.
JTG 3362-2018 is the Chinese standard "Specifications for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts". Its scope clause reads: 1.0.1 The Specifications is developed for regulating the design of reinforced and prestressed concrete highway bridges and culverts to ensure the quality of the projects.
1.0.2 The Specifications is applicable to the design of reinforced and prestressed concrete bridge and culvert structures to be built on classified highways, and is not applicable to the design of bridge and culvert structures made of special concrete.
1.0.3 The limit state design methodology, which is based on the probability theory and expressed with partial factors, is adopted in the Specifications for design purposes.
1.0.4 In addition to the Specifications, the design of reinforced and prestressed concrete bridge and culvert structures shall also comply with the provisions in current relevant national and industry standards.
Found what you need?
Document preview — JTG 3362-2018
National Standard of the People's Republic of China
- Replacing
- JTG D62-2004
Issued by: Ministry of Transport
Contents
- Foreword
- 1 General Provisions
- 2 Terms and Symbols
- 2.1 Terms
- 2.2 Symbols
- 3 Materials
- 3.1 Concrete
- 3.2 Reinforcement
- 4 Basis of Structural Design
- 4.1 General
- 4.2 Analysis of Slabs
- 4.3 Analysis of Beams
- 4.4 Analysis of Arches
- 4.5 Requirements for Durability Design
- 5 Design for Ultimate Limit State in Persistent Situations
- 5.1 General
- 5.2 Flexural Members
- 5.3 Compression Members
- 5.4 Tension Members
- 5.5 Torsion Members
- 5.6 Members Subjected to Punching Shear
- 5.7 Members Subjected to Local Compression
- 6 Design for Serviceability Limit State in Persistent Situations
- 6.1 General
- 6.2 Loss of Prestress
- 6.3 Check for Cracking Resistance
- 6.4 Check for Crack Width
- 6.5 Check for Deflection
- 7 Stress Analysis of Members in Persistent or Transient Situations
- 7.1 Stress Analysis for Prestressed Concrete Members in Persistent Situations
- 7.2 Stress Analysis of Members in Transient Situations
- 8 Requirements for Member Analysis
- 8.1 Composite Flexural Members
- 8.2 Post-tensioned Concrete Anchorage Zones
- 8.3 Diaphragms at Supports
- 8.4 Cap Beams on Piers and Abutments
- 8.5 Pile Caps
- 8.6 Hinges
- 8.7 Bearings
- 8.8 Deck Expansion Joints
- 9 Detailing Requirements
- 9.1 General
- 9.2 Slabs
- 9.3 Beams
- 9.4 Prestressed Concrete Superstructures
- 9.5 Arch Bridges
- 9.6 Columns, Piers and Abutments, Pile Caps
- 9.7 Bearings and Expansion Joints
- 9.8 Culverts, Lifting Loops and Hinges
- Appendix A Practical Refined Analysis Models for Bridge Structures
- Appendix B Analysis Method Using Strut-and-Tie Model
- Appendix C Concrete Shrinkage Strain and Creep Coefficient Calculation, Ratio of Median to Ultimate Values of Prestress Loss due to Prestressing Steel Relaxation
- Appendix D Calculation Formulas for Temperature Actions
- Appendix E Simplified Calculation Formula for Effective Length of Compression Member
- Appendix F Calculation for Compressive Resistance of an Eccentrically Loaded Reinforced Concrete Compression Member of Circular Cross-section with Longitudinal Reinforcement Evenly Distributed along the Perimeter
- Appendix G Simplified Calculation for Loss of Prestress in Curved Tendons due to Anchorage Set, Reinforcement Retraction and Joint Compression after Considering Reverse Friction
- Appendix H Simplified Calculation for Loss of Prestress Due to Elastic Shortening of Concrete in Post-tensioned Members
- Appendix J Calculation for Depth of Compression Zone in Type B Prestressed Concrete Flexural Members Permitted to Crack
- Wording Explanation for the Specifications
- Background to Provisions
- Technical Terms in Chinese and English
- References
Foreword
The revision of Code for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts (JTG D62-2004), pursuant to the "Notice of Planning for Compilation and Amendment Program of Highway Engineering Standards in 2011" (No. 115) issued by the Ministry of Transport of the People's Republic of China in 2006, was carried out by the chief editing organization, CCCC Highway Consultants Co., Ltd.
The revision has been approved and issued as Specifications for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts (JTG 3362-2018) for implementation.
During the revision, the editorial team conducted extensive special studies and research works, reviewed the updated technical development and design experience in China, and referred to relevant domestic and international standards. Upon the completion of the first draft of the Specifications, the drafted specification was circulated for comments from relevant experts and organizations involved in design, construction, maintenance and administration, based on which several rounds of discussion, consultation and updating were conducted before being finalized for approval.
The main revisions made in this version include the following contents: strength grades of reinforcement used in concrete bridges and culverts were updated; basic requirements for the design of bridge structures were added; design requirements for durability of concrete bridges and culverts were emphasized; requirements for checking of overturning resistance of concrete box girder bridges, practical refined analysis methods for complex bridges, design methods for bridges with external tendons, and design methods for disturbed regions of concrete bridges were supplemented; calculation methods for resistance on cross-sections of circular compression members were updated; calculation formulas for determining effective length factors of compression members with different boundary conditions were added; calculation methods for determining crack width in reinforced concrete structures or Type B prestressed concrete structures were adjusted; and requirements for detailing design were supplemented.
Feedback is welcome and will be taken into account in future editions. Please address it to the chief editing organization.
Chief editing organization: CCCC Highway Consultants Co., Ltd.
Associate editing organizations: Tongji University; Southeast University; Research Institute of Highway, Ministry of Transport; Dalian University of Technology; CCCC Highway Bridges National Engineering Research Center Co., Ltd.
1 General Provisions
1.0.1 The Specifications is developed for regulating the design of reinforced and prestressed concrete highway bridges and culverts to ensure the quality of the projects.
1.0.2 The Specifications is applicable to the design of reinforced and prestressed concrete bridge and culvert structures to be built on classified highways, and is not applicable to the design of bridge and culvert structures made of special concrete.
1.0.3 The limit state design methodology, which is based on the probability theory and expressed with partial factors, is adopted in the Specifications for design purposes.
1.0.4 In addition to the Specifications, the design of reinforced and prestressed concrete bridge and culvert structures shall also comply with the provisions in current relevant national and industry standards.
2 Terms and Symbols
2.1 Terms
2.1.1 Reinforcing steel
Non-prestressed reinforcement in concrete structural members.
2.1.2 Prestressing steel
Materials used for applying prestressing forces in concrete structural members, including steel wires, steel strands and steel bars.
2.1.3 Reinforced concrete structure
A concrete structure that contains load-carrying reinforcing steel.
2.1.4 Prestressed concrete structure
A concrete structure that contains prestressing steel that is used to develop prestressing forces by tensioning or other methods.
2.1.5 Limit state
A state beyond which a whole structure or a part of the structure no longer satisfies a certain functional requirement for which it was designed.
2.1.6 Design situation
A set of design conditions that represent the corresponding conditions occurring during a certain time period in the entire process from construction to operation of the structure, for which the design will demonstrate that the relevant limit states are not exceeded.
2.1.7 Characteristic material strength
A basic representative value of material strength adopted in the design of structural members, which is determined using the fractile value with 95 percent level of confidence through statistical analysis of the material strength data obtained by the specified standard test methods for standard specimens.
2.1.8 Partial factor
The factors adopted in the design formulas to ensure the designed structure meets the specified reliability when the probabilistic limit state design method is used. The factors are classified into two types: the partial factor for action and the partial factor for resistance (materials).
2.1.9 Design material strength
The value obtained from the characteristic material strength divided by a partial factor.
2.1.10 Safety level
The level designated to a bridge or culvert in the design according to the severity of consequences of its failure.
2.1.11 Importance factor of structure
A factor which relates to the safety level and is used for adjusting the effects of action combinations in order to achieve a specified reliability of the structure.
2.1.12 Nominal geometric parameter
The basic representative value of a geometrical parameter adopted for the design of a structure or a structural member, which may be taken from the value specified in the design documents.
2.1.13 Design ultimate load-carrying capacity / Design resistance
The ultimate load-carrying capacity of a structure or member calculated using the design value of material strength for its ultimate limit state design.
2.1.14 Cracking moment
The theoretical bending moment when the initial crack appears on a member.
2.1.15 Construction load
Temporary loads applied on a structure or a structural member during construction, which are considered in a structural design for transient situations, including self-weight of the structure, loads of formwork attached to the structure or structural member, construction materials, equipment, personnel, etc.
2.1.16 Durability design
The design to achieve durability of structures or members in the design life, including selection of materials, application of construction measures and implementation of additional protection.
2.1.17 Disturbed region
The region in concrete structures where the sectional strain distribution does not conform to the assumption that plane sections remain plane; it is also referred to as D region.
2.1.18 Strut-and-tie model
A truss model that reflects the force transfer path and force effects in the disturbed regions of a concrete structure.
2.1.19 Bursting force
Transverse tensile forces in the post-tensioned anchorage zone, resulting from the spreading of concentrated anchor forces.
2.1.20 Spalling force
Tensile forces in concrete around base plates, resulting from the compressive deformation ahead of anchorage due to concentrated anchor force in the post-tensioned anchorage zone.
2.1.21 Thickness of concrete cover
Minimum distance between the surface of reinforcement and the surface of the concrete of a member.
2.1.22 Development length
The required length for reinforcement (a reinforcing bar or prestressing tendon) to achieve the design bearing stress by the effect of bonding between its surface and concrete or by the confining effect of its bent end.
Remaining clauses in the full document
- 2.2 Symbols
- 3 Materials
- 4 Basis of Structural Design
- 5 Design for Ultimate Limit State in Persistent Situations
- 6 Design for Serviceability Limit State in Persistent Situations
- 7 Stress Analysis of Members in Persistent or Transient Situations
- 8 Requirements for Member Analysis
- 9 Detailing Requirements
- Appendix A Practical Refined Analysis Models for Bridge Structures
- Appendix B Analysis Method Using Strut-and-Tie Model
- Appendix C Concrete Shrinkage Strain and Creep Coefficient Calculation, Ratio of Median to Ultimate Values of Prestress Loss due to Prestressing Steel Relaxation
- Appendix D Calculation Formulas for Temperature Actions
- Appendix E Simplified Calculation Formula for Effective Length of Compression Member
- Appendix F Calculation for Compressive Resistance of an Eccentrically Loaded Reinforced Concrete Compression Member of Circular Cross-section with Longitudinal Reinforcement Evenly Distributed along the Perimeter
- Appendix G Simplified Calculation for Loss of Prestress in Curved Tendons due to Anchorage Set, Reinforcement Retraction and Joint Compression after Considering Reverse Friction
- Appendix H Simplified Calculation for Loss of Prestress Due to Elastic Shortening of Concrete in Post-tensioned Members
- Appendix J Calculation for Depth of Compression Zone in Type B Prestressed Concrete Flexural Members Permitted to Crack
- Wording Explanation for the Specifications
- Background to Provisions
- Technical Terms in Chinese and English
- References
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 250 pages — is available in the English PDF.
How to Download JTG 3362-2018
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JTG 3431-2024 — Rock test procedures for highway engineering
JTG 3432-2024 — Testing procedures for aggregates in highway engineering
JTG 3441-2024 — Test procedures for inorganic binder stabilized materials for highway engineering
Secure payment via Stripe
Payments accepted
JTG 3362-2018
$3,440.00