JJG 1183-2021Structure height gauges for Railway Frogs (English PDF)
铁路辙叉结构高度测量器检定规程
This is a limited preview
Buy now to download the full PDF (8 pages)
Need quotation for your management?
Get a formal quotation for JJG 1183-2021 in 30 minutes.
Issued by
State Administration for Market Regulation
Level / Type
National · Mandatory
Issue date
December 28, 2021
Implementation date
June 28, 2022
Scope
JJG 1183-2021 is the English-translated version of 铁路辙叉结构高度测量器检定规程.
JJG 1183-2021 is the Chinese standard "Structure height gauges for Railway Frogs". Issued on 2021-12-28, in force from 2022-06-28.
Found what you need?
Document preview — JJG 1183-2021
Contents
- Introduction (II)
- 1 Scope(1)
- 2 Overview(1)
- 3 Measurement performance requirements (1)
- 3.1 Length of main ruler(1)
- 3.2 Measuring range(1)
- 3.3 Surface roughness of working surface (1)
- 3.4 Ruler marks (1)
- 3.5 Distance from the edge of the vernier marking surface to the marking surface of the measuring ruler (2)
- 3.6 Coplanarity of the positioning surfaces of the two positioning rulers (2)
- 3.7 Indication variation (2)
- 3.8 Indication error(2)
- 3.9 Indication repeatability(2)
- 3.10 Drift(2)
- 4 General technical requirements (2)
- 4.1 Appearance(2)
- 4.2 Interaction of each part (2)
- 5 Measuring Instrument Control(2)
- 5.1 Verification Conditions (2)
- 5.2 Verification items (3)
- 5.3 Verification method (3)
- 5.4 Processing of Verification Results (4)
- 5.5 Verification Period(4)
- Appendix A (Reference) Verification Record of Railway Frog Structure Height Measuring Instrument (5)
- Appendix B (Reference) Verification Certificate and Verification Result Notification Inner Page Format (6)
1 Scope(1)
2 Overview(1)
3 Measurement performance requirements (1)
3.1 Length of main ruler(1)
3.2 Measuring range(1)
3.3 Surface roughness of working surface (1)
3.4 Ruler marks (1)
3.5 Distance from the edge of the vernier marking surface to the marking surface of the measuring ruler (2)
3.6 Coplanarity of the positioning surfaces of the two positioning rulers (2)
3.7 Indication variation (2)
3.8 Indication error(2)
3.9 Indication repeatability(2)
3.10 Drift(2)
4 General technical requirements (2)
4.1 Appearance(2)
4.2 Interaction of each part (2)
5 Measuring Instrument Control(2)
5.1 Verification Conditions (2)
5.2 Verification items (3)
5.3 Verification method (3)
5.4 Processing of Verification Results (4)
5.5 Verification Period(4)
Appendix A (Reference) Verification Record of Railway Frog Structure Height Measuring Instrument (5)
Appendix B (Reference) Verification Certificate and Verification Result Notification Inner Page Format (6)
Introduction
This regulation is based on TB/T 3467-2016 "Alloy Steel Combination Frog", TB/T 447-2004 "High Manganese Steel Frog" "Technical Conditions", TG/GW115-2012 "Rules for Repair of Ballastless Track Lines of High-speed Railway" and TG/GW116-in 2013, it was compiled from the relevant requirements in the "Rules for the Repair of Ballasted Track Lines of High-speed Railway".
This regulation is published for the first time.
Rules for the Verification of Height Measuring Instruments for Railway Frog Structures
1 Scope
This regulation is applicable to the initial verification and subsequent verification of the height measuring device of the railway frog structure (hereinafter referred to as the measuring device).
and in-use checks.
2 Overview
The measuring instrument is a special railway measuring instrument used to measure the height difference between the top surface of the frog core rail and the top surface of the wing rail.
The display mode is divided into ruler type measuring instrument and digital measuring instrument. The schematic diagram of its structure is shown in Figure 1 and Figure 2.
Figure 1 Ruler-type measuring device
1,5-positioning ruler;2-main ruler;3-measurement ruler;4-vernier
Figure 2 Digital measuring instrument
1,5-positioning ruler; 2-main ruler; 3-measuring ruler; 4-reading device
3 Measurement performance requirements
3.1 Length of main ruler the length of the main ruler of the measuring instrument should not be less than 300mm.
3.2 Measuring range
The measuring range of the measuring ruler should cover (-15~15) mm.
3.3 Surface roughness of working face the surface roughness Ra value of each working surface of the measuring instrument should not be greater than 0.8µm.
3.4 Ruler Marks
For the ruler type measuring device, the marking width of the measuring ruler and the vernier is (0.12~0.25) mm, and the marking width is different.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 8 pages — is available in the English PDF.
How to Download JJG 1183-2021
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
JJG 1151-2025 — Verification Regulation of Liquid Chromatograph-Atomic Fluorescence Spectrometers
JJG 1204-2025 — Verification Regulation of Electronic Price Computing Scales(for Trial Implementation)
JJG 579-2025 — Trial Case Lenses
JJG 1183-2021
$255.00