Valid

JJG 1089-2013Verification Regulation of Osmometers (English PDF)

渗透压摩尔浓度测定仪

Preview PDF

This is a limited preview

Buy now to download the full PDF (9 pages)

Need quotation for your management?

Get a formal quotation for JJG 1089-2013 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine

Level / Type

National · Mandatory

Issue date

October 25, 2013

Implementation date

January 25, 2014

Scope

JJG 1089-2013 is the English-translated version of 渗透压摩尔浓度测定仪.

JJG 1089-2013 is the Chinese standard "Verification Regulation of Osmometers". Issued on 2013-10-25, in force from 2014-01-25.

Found what you need?

Document preview — JJG 1089-2013

National Standard of the People's Republic of China

ICS
17.020

Contents

  • Introduction (II)
  • 1 Scope (1)
  • 2. References (1)
  • 3 Terminology and units of measurement (1)
  • 4 Overview (1)
  • 5 Metering performance requirements (1)
  • 6 General Requirements (2)
  • 6.1 Appearance (2)
  • 6.2 Boot check (2)
  • 7 Control of measuring instruments (2)
  • 7.1 Verification Conditions (2)
  • 7.2 Verification Project (2)
  • 7.3 Verification Methods (3)
  • 7.4 Test results processing (3)
  • 7.5 Test cycle (3)
  • Appendix A Test original record format (4)
  • Appendix B Test certificates/test results in the notice page format (5)

1 Scope (1)

2 References (1)

3 Terminology and units of measurement (1)

4 Overview (1)

5 Metering performance requirements (1)

6 General Requirements (2)

6.1 Appearance (2)

6.2 Boot check (2)

7 Control of measuring instruments (2)

7.1 Verification Conditions (2)

7.2 Verification Project (2)

7.3 Verification Methods (3)

7.4 Test results processing (3)

7.5 Test cycle (3)

Appendix A test original record format (4)

Appendix B test certificates/test results in the notice page format (5)

Introduction

JJF1002-2010 "national verification procedures write rules", JJF1001-2011 "common terminology and measurement the definition of "together constitute the support of the protocol development of the basic family of specifications.

This procedure of "People's Republic of China Pharmacopoeia" (2010 edition) of the osmolarity of the analyzer requirements as the basis for the development.

This procedure was first formulated.

Osmolality analyzer test procedures

1 Scope

The order applies to the use of the principle of freezing point depression osmolality analyzer (hereinafter referred to as equipment) for the first time Test, test and subsequent use of checks.

2. References

People's Republic of China Pharmacopoeia (2010 edition) Appendix VH osmolarity assay for dated references, only the dated edition applies to this procedure; undated reference documents Member, the latest edition (including any amendments) applies to this procedure.

3 terminology and units of measurement 3.1 capacity osmolarity Osmolarity Per liter of solution refers to the number of moles of solute in the permeate, Osmol·L-1 units or mOsmol·L-1, 1Osmol·L-1 = 1000mOsmol·L-1.

3.2 wt osmolality Osmolality Refers to the solute per kilogram of solvent penetration mole number of units Osmol · kg-1 or mOsmol · kg-1, 1Osmol · kg-1 = 1000mOsmol · kg-1.

4 Overview

The instrument works by indirectly measuring the osmolarity of the solution using the freezing point depression. The temperature measurement Probe immersed in the center of the solution, and fell to the instrument cooling slots. Start the cooling system, when the temperature dropped below freezing solution the next, the instrument uses an oscillator (or metal probe) induced by freezing the solution, automatically record the temperature of the freezing point depression. instrument Data processing system after the temperature of the freezing point depression of the data processed by the terms of osmolality.

Instrument usually consists of refrigeration systems, temperature measurement system, temperature control system, data processing system and a display system and other parts composition.

5 metering performance requirements Instrumental performance indicators are shown in Table 1.

Table 1 test and measurement of project performance indicators

No. test items measured performance indicators

1 Indication error

Not more than 400mOsmol · kg-1 when no more than ± 6mOsmol · kg-1 Concentrations greater than 400mOsmol · kg-1 when no more than ± 1.5%

2 Repeatability <=2mOsmol · kg-1

3 Stability <=2mOsmol · kg-1

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.

How to Download JJG 1089-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
9 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JJG 1089-2013

$205.00