Valid

JJG 1086-2013Verification Regulation of Pneumatic Piston Gauge (English PDF)

气体活塞式压力计

Preview PDF

This is a limited preview

Buy now to download the full PDF (17 pages)

Need quotation for your management?

Get a formal quotation for JJG 1086-2013 in 30 minutes.

Issued by

General Administration of Quality Supervision, Inspection and Quarantine

Level / Type

National · Mandatory

Issue date

July 4, 2013

Implementation date

October 4, 2013

Scope

JJG 1086-2013 is the English-translated version of 气体活塞式压力计.

JJG 1086-2013 is the Chinese standard "Verification Regulation of Pneumatic Piston Gauge". Issued on 2013-07-04, in force from 2013-10-04.

Found what you need?

Document preview — JJG 1086-2013

National Standard of the People's Republic of China

ICS
17.100

Contents

  • Introduction (II)
  • 1 Scope (1)
  • 2. References (1)
  • 3 Overview (1)
  • 4 Metering performance requirements (1)
  • 4.1 Accuracy class (1)
  • 4.2 Effective area of the piston (1)
  • 4.3 Piston and quality fittings and special weight mass (2)
  • 4.4 Degrees vertical piston (2)
  • 4.5 The duration of the rotation of the piston (2)
  • 4.6 Descending speed of the piston (3)
  • 4.7 Identification of the threshold (3)

1 Scope (1)

2 References (1)

3 Overview (1)

4 Metering performance requirements (1)

4.1 Accuracy class (1)

4.2 Effective area of the piston (1)

4.3 Piston and quality fittings and special weight mass (2)

4.4 Degrees vertical piston (2)

4.5 the duration of the rotation of the piston (2)

4.6 Descending speed of the piston (3)

4.7 Identification of the threshold (3)

Tightness 4.8 (3)

A change in piston effective area of 4.9 cycles (3)

5 General technical requirements (3)

5.1 Appearance (3)

5.2 Piston system (4)

5.3 Bearing plate and special weight (4)

6 Control of measuring instruments (4)

6.1 Verification Project (4)

6.2 Test conditions (4)

6.3 Verification Methods (6)

Processing 6.4 Verification Results (11)

6.5 Test cycle (11)

Appendix A to calculate the pressure deformation coefficient (12)

Appendix B test certificates/test results in the notice page and format (13)

Appendix C major cities in China gravitational acceleration (17)

Appendix D for measurement of absolute pressure gauge described (19)

Introduction

JJF1002 "national verification procedures write rules", JJF1001 "common measurement terms and definitions" JJF1008 "Pressure measurement terminology and definitions" and JJF1059 "Evaluation and Expression of Uncertainty in Measurement" common structure Cost procedures developed fundamental series specifications.

The reference to international regulations Organization of Legal Metrology (OIML) International Recommendation "pressure balance" (Pressure Balance) were formulated, using the basic principles which, for specific methods and technical indicators were refined, complement Filling and modification.

Gas piston gauge test procedures

1 Scope

The order applies to the upper limit of the measurement range is not higher than 10MPa, working medium and lubricating medium are gas piston system Body, measure the gauge and/or gas piston gauge of absolute pressure (hereinafter referred to as gauge) initial verification, Use and subsequent verification check.

This procedure does not apply to loading weights or non-rotating piston gauge system.

2. References

This procedure references the following documents.

JJG 99 weight

JJF1001 common measurement terms and definitions JJF1008 pressure measurement terminology and definitions OIMLR110 pressure balance of international recommendations (PressureBalance) for dated references, only the dated edition applies to this procedure; undated reference documents Member, the latest edition (including any amendments) applies to this procedure.

3 Overview

Pressure gauge is the use of hydrostatic equilibrium pressure measurement principle of measuring instruments, generally by the piston system, special Weight, pressure calibration components.

Measuring gauge measuring range lower and upper limits specified by the manufacturer, the upper limit of the measurement range of the general press 1 × 10n, 1.6 × 10n, 2.5 × 10n, 4 × 10n, 6 × 10n (MPa) select series.

4 metering performance requirements 4.1 accuracy class Relations gauge accuracy classes and maximum permissible errors shall comply with the requirements of Table 1

Table 1 Accuracy class and maximum permissible error

Accuracy class maximum permissible error 0.005 ± 0.005% actually measured pressure value 0.01 ± 0.01% actual measured pressure value 0.02 ± 0.02% actual measured pressure value 0.05 ± 0.05% actual measured pressure value 4.2 piston effective area the maximum permissible error and gauge the level of accuracy of the relationship between the effective piston area shall conform to Table 2.1.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.

How to Download JJG 1086-2013

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
17 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JJG 1086-2013

$375.00