JJF 1296-1990Program of Patttern Evaluation of Static Uniaxial Testing Machines. Part 1: Electronic Universal Testing Machines (English PDF)

1 Scope (1)

2 Referenced Documents (1)

3 Terms and symbols (1)

4 Overview (4)

5 Legal management requirements (4)

6 Measurement requirements (5)

7 General Requirements (9)

8 Types of evaluation items (9)

Test conditions and test methods 9 projects (11)

10 Determined the type of evaluation results (19)

11 Original record format type evaluation (19)

Appendix A measuring instrument type evaluation original record format (20)

Introduction

"Static uniaxial testing machine model evaluation outline" framework reference the corresponding test machine state standards and inspection Set procedure consists of the following three parts.

1.JJF 1296.1-2011 of static uniaxial testing machine model evaluation framework - Part 1. electronic universal test Testing machine 2.JJF 1296.2-2011 of static uniaxial testing machine model evaluation framework - Part 2. hydraulic servo universal test Testing machine 3.JJF 1296.3-2011 of static uniaxial testing machine model evaluation framework - Part 3. Hydraulic universal test Testing machine when you use this syllabus for type evaluation test of static uniaxial testing machines, test should be based on the type of machine selection Outline the appropriate section.

This section is about the contents of electronic universal testing machine model evaluation, according JJF 1016-2009 "Measuring Instruments Type evaluation outline guidelines for the preparation ", JJF 1015-2002" Measuring Instruments type evaluation and type approval of universal norms " Requirements, according to the national standard GB/T 16491-2008 "electronic universal testing machine" and the national verification procedures JJG475-2008 "electronic universal testing machine" and compiled. Since the classification test machine more, type More complex, such as the use of the syllabus for type evaluation test does not completely cover all the weighing machine test requirements and technical when requested, should refer to the relevant corporate standards, manuals and other technical documents prepared outline additional provisions as type evaluation Based test.

Static uniaxial testing machine model evaluation outline Part 1. electronic universal testing machine

1 Scope

This outline is applied to the electronic universal testing machine, electronic tensile type approval (or pressure) tester.

2 Citations

JJF 1011-2006 force value and hardness measurement terms and definitions JJG475-2008 electronic universal testing machine GB/T 2611-2007 General requirements for testing machines GB 5226.1-2008 Safety of machinery - Electrical machinery and electrical equipment - Part 1. General requirements (IEC 60204-1:2005, Safetyofmachinery-Electricalequipmentofmachines-Part 1.

Generalrequirements, IDT) GB/T 13634-2008 uniaxial testing machines dynamometer calibration standard (ISO 376:2004, Metalicmaterials-calibrationofforce-provinginstrumentsusedfortheverificationof uniaxialtestingmachines, IDT) GB/T 16491-2008 electronic universal testing machine GB/T 16825.1-2008 static uniaxial testing machines - Part 1. Tension (or) pressure test Testing machine measuring system test and calibration (ISO 7500-1:2004, Metalicmaterials-Verificationof staticuniaxialtestingmachines-Part 1. Tension/compressiontestingmachines-Verifi-cationandcalibrationoftheforce-measuringsystem, IDT) GB/T 17200-2008 Rubber plastic tensile, compression and bending test machine (constant speed drive) Technical Specifications (ISO 5893:2002, Rubberandplasticstestequipment-Tensile, flexuralandcompres-siontypes (constantrateoftraverse) -Specification, IDT) Evaluation of GB/T 22066-2008 static uniaxial testing machine with computer data acquisition system JB/T 6146-2007 Technical requirements extensometer these documents contain provisions which through reference in this syllabus constitute provisions of this outline. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this syllabus, however, the drum Reed whether the latest versions of these files according to the parties that this outline agreement. Those who do not note cited date Use, the latest versions apply to this outline.

3 Terms and symbols

3.1 Terms and Definitions the following terms and definitions apply to this outline.

Resolution Indication means may be the ability to meaningfully distinguish indicates the amount of two adjacent values.