Valid

JB/T 8599.2-1997CNC copying bed-type milling machines - Technical specifications (English PDF)

数控仿形床身铣床 技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 8599.2-1997 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

August 18, 1997

Implementation date

August 18, 1997

Scope

JB/T 8599.2-1997 is the English-translated version of 数控仿形床身铣床 技术条件.

JB/T 8599.2-1997 is the Chinese standard "CNC copying bed-type milling machines - Technical specifications". Its scope clause reads: This standard specifies the requirements for the manufacture and acceptance of numerically controlled profiling bed-type milling machines.

It applies to general-purpose numerically controlled profiling bed-type milling machines with a table width of 320 mm to 1 250 mm.

Found what you need?

Document preview — JB/T 8599.2-1997

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • 1 Scope
  • 2 Normative references
  • 3 General requirements
  • 4 Accessories and tools
  • 5 Machining and assembly quality

1 Scope

This standard specifies the requirements for the manufacture and acceptance of numerically controlled profiling bed-type milling machines.

It applies to general-purpose numerically controlled profiling bed-type milling machines with a table width of 320 mm to 1 250 mm.

2 Normative references

The provisions contained in the following standards become provisions of this standard through reference in this standard. The editions shown were valid at the time of publication of this standard. All standards are subject to revision, and the parties using this standard should consider the possibility of applying the latest editions of the standards listed below.

GB 9061-88 General specifications for metal-cutting machine tools

JB/T 8599.1-1997 Numerically controlled profiling bed-type milling machines - Accuracy inspection

ZB J50 003-88 Determination of the cleanliness of metal-cutting machine tools

ZBn J50 008.1-88 General specifications for machined parts of metal-cutting machine tools

ZBn J50 008.3-88 General specifications for the assembly of metal-cutting machine tools

3 General requirements

When a machine is accepted in accordance with this standard, the remaining acceptance items of GB 9061, ZBn J50 008.1 and ZBn J50 008.3 that are not made specific by this standard shall also be inspected.

4 Accessories and tools

4.1 Accessories and tools supplied with the machine

The following are supplied with the machine: a) one set of milling cutter arbors; b) one draw stud for the 7:24 taper shank; c) one tracer finger; d) one set of foundation bolts and levelling wedges; e) one set of special adjusting tools.

4.2 Special accessories supplied by agreement

The following special accessories may be supplied by agreement: a) special cutting tools; b) a tool setting device; c) tracer fingers of various kinds; d) peripheral equipment for the control system; e) others.

5 Machining and assembly quality

The bed, table, column, spindle headstock, saddle, the slide of the column or spindle head, and the ram are important castings or welded assemblies and shall be stress-relieved after rough machining.

The parts of the machine subject to wear, such as the spindle, the spindle quill, the screw and nut assembly and the high-speed, heavily loaded gears, shall be given wear-resistance treatment appropriate to their service life.

The following guideway pairs are important and shall be given wear resistance by the use of wear-resistant cast iron, steel inserts, plastic coating or high- or medium-frequency induction hardening: a) table to saddle; b) saddle to bed; c) column (or column slide) to bed; d) ram to vertical slide; e) vertical slide to column; f) table to bed; g) spindle headstock to column.

The mating faces of the sliding guideway clamping plates and the mating face between the tracer bracket and the spindle headstock shall be assessed as "important fixed mating faces".

The following shall be assessed as "particularly important fixed mating faces": a) the mating face of the screw bracket; b) the mating face of the nut seat; c) the mating face between column and bed; d) the mating face between the front and rear beds; e) the mating face between the column and the column slide; f) the mating face between the spindle headstock and its slide.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

Similar standards

How to Download JB/T 8599.2-1997

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
15 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

JB/T 8599.2-1997

$369.00