Valid

JB/T 10416-2004Coil springs for suspensions - Technical requirements (English PDF)

悬架用螺旋弹簧技术条件

Preview PDF

This is a limited preview

Buy now to download the full PDF (15 pages)

Need quotation for your management?

Get a formal quotation for JB/T 10416-2004 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

October 20, 2004

Implementation date

April 1, 2005

Scope

JB/T 10416-2004 is the English-translated version of 悬架用螺旋弹簧技术条件.

JB/T 10416-2004 is the Chinese standard "Coil springs for suspensions - Technical requirements". Its scope clause reads: This standard specifies the specification, test method, marking, packaging as well as test and inspection rule of automobile suspension spring (hereinafter referred to as spring).

This standard is applicable to automobile suspension spring (hereinafter referred to as spring). Its clauses include specification.

Found what you need?

Document preview — JB/T 10416-2004

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Foreword I
1 Scope
2 Normative References
3 Specification
3.1 Materials
3.2 Dimension Parameters and Tolerances
3.3 Characteristic Requirements
3.4 Hardness and Decarburization
3.5 Fatigue Life and Looseness
3.6 Surface Anti-corrosion Treatment
4 Test Methods
4.1 Dimension
4.2 Characteristics
4.3 Hardness and Decarburization
4.4 Fatigue Test
4.5 Surface Anti-corrosion Test
5 Inspection Rules
5.1 Classification of Inspection Rules
5.2 Defects
6 Marking, Packaging, Transportation and Storage
6.1 Marking
6.2 Packaging
6.3 Transportation
6.4 Storage
6.5 Other
Figure 1 End Shape of Hot-rolled Spring

1 Scope

This standard specifies the specification, test method, marking, packaging as well as test and inspection rule of automobile suspension spring (hereinafter referred to as spring).

This standard is applicable to automobile suspension spring (hereinafter referred to as spring).

2 Normative References

The following normative documents contain provisions which, through reference in this text, constitute provisions of this standard. For dated references, subsequent amendments to (excluding amending errors in the text), or revisions of, any of these publications do not apply. However, all parties coming to an agreement according to this standard are encouraged to study whether the latest edition of the normative document is applicable. For undated references, the latest edition of the normative document applies.

GB/T 224 Determination of Depth of Decarburization of Steel

GB/T 230 Metallic Materials - Rockwell Hardness Test (GB/T 230-991, neq ISO 6508:1986)

GB/T 231.1 Metallic Materials - Brinell Hardness Test - Part 1: Test Method (GB/T 231.1-2002, eqv ISO 6506-1:1999)

GB/T 1222 Spring Steels (GB/T 1222-1984, neq ISO 4801:1977)

JB/T 7944 Sampling Procedures for Inspection by Attributes of Coiled Helical Springs

QC/T 484-1999 Automobiles Paint Coating

3 Specification

3.1 Materials

3.1.1

Materials specified in GB 1222 or those approved by the customer shall be adopted for spring materials.

3.1.2

Materials must be provided with quality guarantee given by the material manufacturer and may only be used after passing the re-inspection.

3.2 Dimension Parameters and Tolerances

3.2.1 End ring diameter

The diameter tolerance of spring end ring is ±1.5mm.

3.2.2 Total number of coils

Tolerance of the total number of coils for spring is ±1.2% of the total number of coils n1. For spring with unground end ring and installed in irrotational seat, such tolerance shall be strictly required to be ±0.5% of the total number of coils n1.

3.2.3 Pitch uniformity

Where the equal-pitch spring without sheath is compressed to the maximum load, its normal pitch shall not be contacted. The equal-pitch spring with sheath is subject to negotiation between supplier and purchaser.

3.2.4 End ring grinding surface

For grinded spring with tight end ring, the roughness of grinding surface Ra is not less than 6.3µm, the grinding range is not less than 270° and the end thickness shall be (1/4)d±2mm.

3.2.5 Axis straightness

For cylindrical spring under free state, the axis straightness tolerance of spring shall not be greater than 1.5% of the free height H0.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.

How to Download JB/T 10416-2004

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.