HJ 855-2017Technical specification for application and issuance of pollutant permit electroplating industry (English PDF)

Foreword

In order to implement the Environmental Protection Law of the People's Republic of China, the Law of the People's Republic of China on the Prevention and Control of Atmospheric Pollution, People's Republic of China Water Pollution Control Law "and other laws and regulations and the" General Office of the State Council on the issuance of control of pollutant discharge permit system (National Office issued [2016] 81), improve the sewage permit technical support system, to guide and regulate the plating Industrial sewage unit sewage permit application and issuance work, the development of this standard.

This standard specifies the discharge of sewage discharge units and special treatment of electroplating wastewater centralized sewage treatment plant sewage permit the basic information of the application and the issuance of the certificate, the determination of the allowable emission limit, the actual discharge accounting, the method of compliance judgment as well as self-monitoring, environmental management desk and discharge permit implementation report and other environmental management requirements, put forward the electroplating industry pollution Prevention and control of feasible technical requirements.

Issued by the issuing authority issued a permit, the laws and regulations are clearly prohibited in the construction area, belonging to the state or where the local Party has clearly stipulated that the discharge unit or the production process of the electroplating industry to be eliminated or banned shall not be allowed to issue a sewage permit certificate.

Appendix A to E of this standard are informative.

This standard is the first release.

This standard is organized by the Planning and Finance Department of the Ministry of Environmental Protection and the Ministry of Environmental Protection.

The main drafting unit of this standard. Beijing North Energy Conservation Environmental Protection Co., Ltd., Environmental Protection Department Environmental Engineering Assessment Center, Ring Environmental Protection Institute of Environmental Standards, China Environmental Protection Industry Association.

The environmental protection department of this standard approved on September 12, 2017.

This standard has been implemented since September 12, 2017.

This standard is explained by the Ministry of Environmental Protection.

Sewage Permit Application and Issuance Technical Specification Electroplating Industry

1 Scope of application

This standard specifies the discharge of sewage discharge units and special treatment of electroplating wastewater centralized sewage treatment plant sewage permit the basic information of the application and the issuance of the certificate, the determination of the allowable emission limit, the actual discharge accounting, the method of compliance judgment as well as self-monitoring, environmental management desk and discharge permit implementation report and other environmental management requirements, put forward the electroplating industry pollution Prevention and control of feasible technical requirements.

This standard applies to the centralized discharge of sewage treatment units and special treatment of electroplating wastewater treatment plant reported "Sewage permit application form" and fill in the relevant application information online, applicable to the guidance of the issuing authority to determine the electroplating industry Sewage units and special treatment of electroplating wastewater centralized sewage treatment plant sewage permit requirements.

This standard applies to electroplating industry sewage units and special treatment of electroplating wastewater centralized sewage treatment plant emissions of water Pollutants, air pollutants permit management.

This standard does not make the provisions of the discharge of industrial waste water, waste gas plating industry sewage other units of sewage facilities and discharge, refer to the "sewage permit application and issuance of technical specifications" to implement.

2 Normative reference documents

The contents of this standard refer to the following documents in the provisions of any reference to the date of the document, the effective version of the applicable standard.

Comprehensive Emission Standard for Wastewater GB 13271 Boiler Air Pollutant Emission Standard Emission Standard for Electroplating Pollutants Determination of particulate matter and sampling method of gaseous pollutants in exhaust gas of fixed pollution sources GB/T 16157 GB/T 31962 Sewage Discharge Standard for Urban Sewerage Emission standard for odorous pollutants GB 14554 Technical Guidelines for Unorganized Emissions Monitoring of Air Pollutants HJ/T 75 fixed pollution sources flue gas discharge continuous monitoring technical specifications (Trial) HJ/T 76 fixed pollution source flue gas emissions continuous monitoring system technical requirements and testing methods (Trial) Technical specification for surface water and wastewater monitoring Technical specification for monitoring total water pollutant discharge HJ/T 353 water pollution source on-line monitoring system installation technical specifications (Trial) HJ/T 354 Water Pollution Source Online Monitoring System Acceptance Technical Specification (Trial) HJ/T 355 water pollution source on-line monitoring system operation and assessment of technical specifications (Trial) HJ/T 356 Water pollution source online monitoring system data validity judgment technical specification (Trial) Technical specification for HJ/T 397 fixed source exhaust gas monitoring Technical Guidance for Water Quality Sampling Technical specification for water quality sampling scheme design of HJ 495 General guidelines for self - monitoring of sewage disposal units Technical Guideline for Self - Monitoring of Sewage Discharge Unit HJ -BAT-11 electroplating industry pollution prevention and control of the best feasible technical guidelines (Trial) General rules for application and issuance of sewerage permits HJ - - Discharge Unit Self-Monitoring Technical Guide Electroplating Industry HJ - - Environmental Management Account and Discharge Permit Implementation Report Technical Specification (Trial) "" Thirteen five "eco-environmental protection plan" (Guo Fa [2016] 65) "Fixed pollution source pollution permit classification management directory (2017 version)" (Ministry of Environmental Protection Order No. 45) Notice on Strengthening the Automatic Monitoring of Elevated Source Pollutants in Beijing, Tianjin and Hebei Provinces number) "Reply to the question of the special discharge limit for the implementation of air pollutants" (Circular No. 1087) [ "On the implementation of thermal power, paper industry and the Beijing-Tianjin-Hebei pilot cities elevated source sewage permit management notice" (ring Water body [2016] 189) "Notice on the Implementation of Special Limitation of Emissions of Air Pollutants" (Announcement No. 14 of 2013) "Notice on the implementation of national pollutant discharge standards for special discharge limits for water pollutants in the Taihu Lake Basin" (Announcement No. 30 of 2008) "Notice on the Implementation of the Special Emission Limits of Water Pollutants in the Taihu Lake Basin" (Announcement.2008 no. 28) "Pollution source automatic monitoring facilities operation and management approach" (Central [2008] No. 6) "Sewage outfall standardization of technical requirements (Trial)" (Environmental Monitoring [1996] No. 470)

3 Terms and definitions

The following terms and definitions apply to this standard.

4 Sewage unit basic situation to fill the requirements

5 Heat treatment equipment

Operating voltage range. V Maximum input current. A Maximum input power. kW

6 Degassing tank

amount

Size. mm

7 Rust tank

amount

Size. mm

8 Pickling tank

amount

Size. mm

9 Roughening tank

amount

Size. mm

10 Sensitized tank

amount

Size. mm

11 Activation tank

amount

Size. mm

12 in the slot

amount

Size. mm

13 Prepreg

amount

Size. mm

14 Wash the tank

amount

Size. mm

15 Other (business to fill in) other (business to fill out)

Plating treatment

Plating tank

amount

Size. mm

17 Water tank

amount

Size. mm

18 Other (business to fill in) other (business to fill out)

Post-processing

Passivation tank

amount

Size. mm

20 Coloring trough

amount

Size. mm

21 Closed slot

amount

Size. mm

22 in the slot

amount

Size. mm

Continued

No. Major production unit Main process Production facility Facility parameters Electroplating production line Post-processing Degassing tank amount Size. mm

24 Electrolytic cell

amount

Size. mm

25 Water tank

amount

Size. mm

26 Dehydration equipment Motor power. kW

27 Drying equipment power. kW

28 Drying equipment power. kW

29 in addition to hydrogen equipment power. kW 30 other (business to fill in) other (business to fill out) Supporting system Solution Filtration equipment Filtration area. m2 32 electroplating ultrasonic cleaning machine power. kW 33 sewage treatment facilities Quantity. Table (sets) Processing capacity. m3 wastewater/h

34 Exhaust gas purification facilities

Quantity. Table (sets) Processing capacity. m3 air volume/h Common unit Heating facilities boilers amount Maximum continuous evaporation. t/h Storage facilities Chemicals Temporary storage area. m2 37 coal field, ash field covers an area. m2 38 hazardous waste storage room (library) Area. m2 Auxiliary facilities Primary rainwater collection pool amount Effective volume. m3 40 emergency disaster pool amount Effective volume. m3

4.3.3 Product name

Hardware parts, communication accessories, electronic components and components, jewelry pieces, lighting and accessories, bathroom plumbing parts, transportation Equipment spare parts and accessories, household appliances, metal products, furniture products, plastic products, defense products spare parts and Accessories and so on.

4.3.4 Production capacity and unit of measurement Fill in the design capacity, not including the national or local government to be eliminated or banned capacity. The unit of measure is area.

4.3.5 years design and production time Environmental impact assessment documents and approval, the local government on the identification of illegal projects or filing documents to determine the design of the annual production between.

4.3.6 other

Electroplating industry sewage unit if necessary, can be filled out.

4.4 Main raw and auxiliary materials and fuels Raw and auxiliary materials and fuel types, name, design use is required, the proportion of sulfur, toxic and harmful ingredients and Percentage of optional items.

4.4.1 Species

Divided into raw materials, fuel.

4.4.2 Raw materials

4.4.2.1 Name

Electroplating commonly used raw materials, accessories can be selected in Appendix B, such as Appendix B does not have their own fill.

Excipients should also include waste gas, chemical additives added during the wastewater treatment, such as ferrous sulfate, sodium bisulfite, hydrogen Sodium oxide, sodium carbonate, hydrated lime, coagulant, flocculant, coagulant, others and the like.

4.4.2.2 Designed for use should be completed in the design of raw and auxiliary materials used.

4.4.2.3 Ingredients

Electroplating industry sewage unit can fill the main raw and auxiliary materials in the chromium, nickel, cadmium, silver, lead, mercury, copper, zinc and other toxic and harmful Composition and proportion. Can refer to the design value or the actual use of the previous year to fill in the report.

4.4.2.4 Main raw material utilization can be filled with copper utilization, zinc utilization (before passivation), nickel utilization, chromium utilization and other major raw material utilization.

4.4.3 Fuel

4.4.3.1 Name

Divided into coal, diesel, heavy oil, natural gas, other.

4.4.3.2 years design usage the annual design usage of the fuel should be reported.

4.4.3.3 Ingredients

Should fill the fuel ash, sulfur, volatile, calorific value, can refer to the design value or the actual use of the previous year to fill in.

4.4.4 other

Electroplating industry sewage unit if necessary, can be filled out.

4.5 sewage disposal nodes, pollutants and pollution control facilities

4.5.1 General principles Waste gas production and emission links, pollutants and pollution control facilities, including plating production facilities corresponding to the pollution-producing links, pollution species Class, type of emissions (organized, unorganized), pollution control facilities, whether feasible technology, organized emission port number, Whether the discharge port meets the requirements and the type of discharge port.

Wastewater includes waste water type, pollutant type, emission destination, pollution control facility, whether it is feasible technology, Number, discharge port settings are standardized and discharge port type.

4.5.2 Exhaust gas

4.5.2.1 Waste gas production link name, emission form, pollutant type and pollution control facilities Electroplating industry Drainage unit Waste gas production link name, emission form, pollutant type and pollution control facility See Table 2. Electroplating industry sewage unit pollutants according to GB 21900 and GB 13271 to determine, there are local emission standards to Seeking, in accordance with local emission standards to determine.

4.5.2.2 Pollution control facilities, organized discharge port number Pollution control facility number can be filled into the internal number of the electroplating industry sewage unit, if no internal number, according to "on the open Exhibition of thermal power, paper industry and the Beijing-Tianjin-Hebei pilot cities elevated source sewage permit management notice "Annex 4" fixed pollution Source (water, atmospheric) coding rules (trial) "to be numbered and reported.

The number of the organization's discharge port should fill in the existing number of the local environmental protection authority, if the local environmental protection authority is not on the discharge port number, according to the "on the thermal power, paper industry and the Beijing-Tianjin-Hebei pilot cities elevated source sewage permit Management of the work of the notice "Annex 4" fixed source of pollution (water, atmospheric) coding rules (Trial) "to be numbered and fill out.

4.5.2.3 Discharge port setting requirements According to the "sewage outfall standardization of technical requirements (Trial)" and the discharge of industrial discharge units to implement the emission standards the provisions of the standardization of the discharge port, fill in the exhaust emission settings are in line with the requirements of standardization.

4.5.2.4 Type of discharge port the exhaust port is divided into the main discharge port and the general discharge port. The main discharge port for the discharge...