Valid

HG/T 5633-2019Shell-and-tube silicon carbide heat exchangers (English PDF)

列管式碳化硅换热器

Preview PDF

This is a limited preview

Buy now to download the full PDF (16 pages)

Need quotation for your management?

Get a formal quotation for HG/T 5633-2019 in 30 minutes.

Issued by

MIIT

Level / Type

Industry · Recommended

Issue date

December 24, 2019

Implementation date

July 1, 2020

Scope

HG/T 5633-2019 is the English-translated version of 列管式碳化硅换热器.

HG/T 5633-2019 is the Chinese standard "Shell-and-tube silicon carbide heat exchangers".

Its scope clause reads: This standard specifies terms and definitions, types, main dimensions and basic parameters, raw materials, design, manufacturing, inspection and acceptance, packaging, transportation, storage, and quality documents of tubular silicon carbide heat exchangers (hereinafter referred to as "heat exchangers").

This standard is applicable to tubular heat exchangers whose nominal diameter is not greater than 900 mm and whose silicon carbide tubes are adopted as components of heat exchange.

This standard is not applicable to heat exchangers with extremely hazardous media except for sulfuric acid.

This standard is applicable to the design pressure of heat exchanger as follows: a) For sulfuric acid, highly hazardous media, gas and liquefied gas and other media, the working pressure at the side of medium should be less than 0.1MPa; b) For media except for Item a), the design pressure should not be greater than 1.6MPa and the maximum working temperature of medium should be less than its normal boiling point. Its clauses include terms and definitions.

Found what you need?

Document preview — HG/T 5633-2019

National Standard of the People's Republic of China

Issued by: Ministry of Industry and Information Technology of the People's Republic of China

Contents

  • 1 Scope
  • 1.4 This standard is applicable to the design pressure of heat exchanger as follows:
  • 1.5 This standard is applicable to the design temperature of heat exchanger as follows:
  • 2 Normative references
  • 3 Terms and definitions
  • 3.1 Silicon carbide
  • 3.2 Free silicon
  • 3.3 Design temperature

1 Scope

1.1

This standard specifies terms and definitions, types, main dimensions and basic parameters, raw materials, design, manufacturing, inspection and acceptance, packaging, transportation, storage, and quality documents of tubular silicon carbide heat exchangers (hereinafter referred to as "heat exchangers").

1.2

This standard is applicable to tubular heat exchangers whose nominal diameter is not greater than 900 mm and whose silicon carbide tubes are adopted as components of heat exchange.

1.3

This standard is not applicable to heat exchangers with extremely hazardous media except for sulfuric acid.

1.4

This standard is applicable to the design pressure of heat exchanger as follows:

a) For sulfuric acid, highly hazardous media, gas and liquefied gas and other media, the working pressure at the side of medium should be less than 0.1MPa;

b) For media except for Item a), the design pressure should not be greater than 1.6MPa and the maximum working temperature of medium should be less than its normal boiling point.

1.5

This standard is applicable to the design temperature of heat exchanger as follows:

a) The shell of the heat exchanger is steel vessel, which should meet the requirements of GB/T 150 code;

b) The shell of the heat exchanger is glass lined vessel, which should meet the requirements of GB 25025 code;

c) The shell of the heat exchanger is fluoroplastic lined vessel, which should meet the requirements of GB/T 35974.2 code;

d) The shell of the heat exchanger is rubber lined vessel, which should meet the requirements of HG/T 20677 code.

2 Normative references

The following referenced documents are indispensable for the application of this document.

For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

GB/T 150.1 Pressure vessels - Part 1: General requirements

GB/T 150.2 Pressure vessels - Part 2: Materials

GB/T 150.3 Pressure vessels - Part 3: Design

GB/T 150.4 Pressure vessels - Part 4: Fabrication, inspection and testing, and acceptance

GB/T 151 Heat exchangers

GB/T 3045 Conventional abrasive - Chemical analysis of silicon carbide

GB/T 10610 Geometrical product specifications(GPS) - Surface texture:Profile method - Rules and procedures for the assessment of surface texture

GB 25025 Specification of glass-lined equipment for industry

GB/T 26501 General technical specification for pressure vessels lined with fluoroplastics

GB/T 35974.2 Plastics and plastic lining pressure vessels - Part 2: Material

GB/T 35974.5 Plastics and plastic lining pressure vessels - Part 5: Fabrication, inspection and testing for pressure vessels with plastic lining

HG/T 20592 Steel pipe flanges (PN designated)

HG/T 20677 Design code for chemical equipment with rubber lining

JB/T 4712.1 Vessel supports - Part 1: Saddle support

JB/T 4712.3 Vessel supports - Part 3: Lug support

JB/T 4711 Coating and packing for pressure vessels transport

JB/T 4732 Steel Pressure Vessels - Design by Analysis

JC/T 2212 Solid - state pressureless sintered sillicon carbide ceramic heat exchanger tubes

NB/T 47003.1 Steel welded atmospheric pressure vessels

3 Terms and definitions

For the purposes of this document, the terms and definitions given in GB/T 150.1, GB/T 151 and the following apply.

3.1 Silicon carbide

A chemical compound formed by the reaction of silicon dioxide with carbon at temperatures above 2000°C.

3.2 Free silicon

An unreacted monomer of silicon molecules present in silicon carbide.

3.3 Design temperature

Design temperature of metal parts is the same as GB/T 150.1 code, design temperature of metal lining parts, including glass lining parts, is the highest temperature that the lining layer can reach; Design temperature of tubes is the highest temperature that the wall of tubes can reach. Both design temperature and design pressure are design load conditions of heat exchanger designing.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 16 pages — is available in the English PDF.

Similar standards

How to Download HG/T 5633-2019

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
16 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

HG/T 5633-2019

$295.00