HG/T 20607-2009PTFE envelope gaskets for use with steel pipe flanges (PN designated) (English PDF)
钢制管法兰用聚四氟乙烯包覆垫片(PN系列)
This is a limited preview
Buy now to download the full PDF (3 pages)
Need quotation for your management?
Get a formal quotation for HG/T 20607-2009 in 30 minutes.
Issued by
Ministry of Industry and Information Technology of the People's
Level / Type
National · Recommended
Issue date
February 5, 2009
Implementation date
July 1, 2009
Scope
HG/T 20607-2009 is the English-translated version of 钢制管法兰用聚四氟乙烯包覆垫片(PN系列).
HG/T 20607-2009 — This national standard specifies pattern, dimension, and technical requirement and marking of PTFE envelope gasket for use with steel pipe flanges (PN designated).
This Standard is applicable to PTFE envelope gasket for use with steel pipe flange with raised face in nominal pressure of PN6~PN40 and in working temperature of less than or equal to 150 specified in HG/T 20592. °C Note. the use of the asbestos-contained material shall comply with requirements of relevant laws and regulations.
When the production and use are containing asbestos material gasket, protective measures shall be adopted, so as to ensure not endanger the person health.
Found what you need?
Document preview — HG/T 20607-2009
National Standard of the People's Republic of China
Issued by: Ministry of Industry and Information Technology of the People's
Contents
- 1. Scope
- 2. Normative references
- 3. Gasket pattern and dimension
- 4. Technical requirement
- 5. Marking and packaging
- 1. Scope
1 Scope
This national standard specifies pattern, dimension, and technical requirement and marking of PTFE envelope gasket for use with steel pipe flanges (PN designated).
This Standard is applicable to PTFE envelope gasket for use with steel pipe flange with raised face in nominal pressure of PN6~PN40 and in working temperature of less than or equal to 150 specified in HG/T 20592. °C Note. the use of the asbestos-contained material shall comply with requirements of relevant laws and regulations. When the production and use are containing asbestos material gasket, protective measures shall be adopted, so as to ensure not endanger the person health.
2 Normative references
The following standards contain provisions which, through reference in this text, constitute provisions of this Standard. For dated reference, subsequent amendments (excluding content of corrigenda) to, or revisions of, any of these publications do not apply.
However, Parties to agreements biased on this Code are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. For undated references, the latest edition of the normative document referred to applies.
"Compressed Asbestos Fibre Jointing" GB/T 3985 "Non-metallic PTFE Envelope Gaskets for Pipe Flanges" GB/T 13404 "Steel Pipe Flanges (PN designated)" HG/T 20592 "Specification for selection of Steel Pipe Flanges, Gaskets and Bolting (PN designated)" HG/T 20614 "PTFE Sheets" QB/T 3625 "PTFE Rods" QB/T 3626
3 Gasket pattern and dimension
3.0.1 According to the type of cutting process, the gasket pattern is consisted of sectioning
type, machining type and fold-packaging type, which are respectively denoted by A-type, B-type and C-type, Figure3.0.1. A-type and B-type are applicable to occasion in nominal dimension of less than or equal to DN500, B-type is recommended to be adopted; while C-type is applicable to occasion in nominal dimension of greater than or equal to DN350.
3.0.2 Gasket dimension
1 The dimensions of A-type, B-type and C-type gasket comply with the requirements of
Table 3.0.2-1 and Table 3.0.2-2.
2 The gasket thickness T shown in Table 3.0.2-1 and Table 3.0.2-2 is recommended
Table 3.0.2-2 Dimension of PTFE Envelope Gaskets (C-type) (mm)
Nominal
dimension
Inside diameter of the coating 1D Outside diameter of the coating 3D mm Outside diameter of the gasket 4D Gasket thickness T Nominal pressure PN 350 377 412 423 438 444 457 474 400 426 469 473 489 495 514 546 450 480 528 528 539 555 564 571 500 530 578 578 594 617 624 628 600 630 679 679 695 734 731 747 Note. The gasket thickness T listed in the table is the recommended gasket thickness. The users may specify other gasket thickness, but that shall be indicated when ordering.
4 Technical requirement
4.0.1 PTFE coating material shall comply with the requirements of FSB-2 and QB/T 3626
specified in QB/T 3625.
4.0.2 The embedded layer or core materials are generally asbestos rubber sheet or non-asbestos fiber sheet. If the user has any special requirement, other appropriate materials may be adopted, but that shall be indicated when ordering.
4.0.3 The dimension tolerances of the inside diameter D1 and outside diameter D4 of the gasket are in accordance with those specified in Table 4.0.3. The coating thickness tolerance is ±0.05mm and the gasket thickness tolerance is ±0.25mm.
4.0.4 The coating surface shall be level up, lubricate, buckling deformation-free, even in thickness and disallow defects like perforated hole and slag inclusion.
4.0.5 The compression rate, resilience, stress relaxation rate and seal leakage rate of the gaskets shall comply with the requirements of GB/T 13404.
Table 4.0.3 Dimension Tolerances of Inside Diameter D1 and Outside Diameter D2 of the Gaskets (mm)
Nominal dimension DN <=300 >=350 Inside diameter of the coating 1D ±1.5 ±3.0 Outside diameter of the gasket 4D +1.5 +3.0
5 Marking and packaging
5.0.1 The gaskets shall be packed according to pattern, specification and material respectively;
when being delivered, it shall be attached with production quality test certificate. The gaskets shall indicate content specified in 5.0.2 by labels.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 3 pages — is available in the English PDF.
Referenced standards
How to Download HG/T 20607-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 13404-2008 — Non-metallic PTFE envelope gaskets for pipe flanges
GB/T 3985-2008 — Compressed asbestos fibre jointing
GB/T 39850-2021 — Core components business document assembly technical specification for international trade
Secure payment via Stripe
Payments accepted
HG/T 20607-2009
$45.00