Valid

GB/T 6346.2601-2018Fixed capacitors for use in electronic equipment -- Part 26-1: Blank detail specification -- Fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte -- Assessment level EZ (English PDF)

电子设备用固定电容器第26-1部分：空白详细规范导电高分子固体电解质铝固定电容器评定水平EZ

Preview PDF

This is a limited preview

Buy now to download the full PDF (30 pages)

Need quotation for your management?

Get a formal quotation for GB/T 6346.2601-2018 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

June 7, 2018

Implementation date

January 1, 2019

Scope

GB/T 6346.2601-2018 is the English-translated version of 电子设备用固定电容器第26-1部分：空白详细规范导电高分子固体电解质铝固定电容器评定水平EZ.

GB/T 6346.2601-2018 is the blank detail specification for fixed aluminium electrolytic capacitors with a conductive polymer solid electrolyte at assessment level EZ, the companion to the surface mount Part 25-1, and an identical adoption of IEC 60384-26-1:2010.

Like every blank detail specification it supplies the format and the minimum content a detail specification has to carry rather than requirements for one capacitor: the numbered boxes of the front page, the recommended mounting method, the case codes and dimensions, the capacitance and voltage values tied to each case code, the characteristics and further requirements, marking, ordering information, the release batch certification record and the quality conformance inspection schedule.

It goes with the sectional specification GB/T 6346.26-2018 and corrects the group sizes p and n in Table 5. It was issued on 7 June 2018 and has applied since 1 January 2019.

Found what you need?

Document preview — GB/T 6346.2601-2018

National Standard of the People's Republic of China

ICS: 31.060.50
Classification: L 11

Issued by: State Administration for Market Regulation, China National Standardization Administration

Foreword
1 General data
1.1 Recommended installation method (should be explained)
1.2 Size
1.3 Ratings and characteristics
1.4 Normative references
1.5 mark
1.6 Ordering Information
1.7 release batch certification record
1.8 Additional content (not for inspection)
1.9 Supplement or improve the severity or requirements specified in the general specification and/or sub-specification
2 Inspection requirements
2.1 Procedure
Reference

Foreword

The National Standard for Fixed Capacitors for Electronic Equipment is divided into the following sections.

--- Part 1. General specification (IEC 60384-1:2008);

--- Part 2. Specification of metallized polyethylene terephthalate film dielectric DC fixed capacitors (GB/T 7332-2011/ IEC 60384-2:2005);

--- Part 2-1. Blank detail specification of metallized polyethylene terephthalate film dielectric DC fixed capacitors E and EZ (GB/T 7333-2012/IEC 60384-2-1:2005);

---Part 3. Sub-standard surface mounting (MnO2) solid electrolyte fixed capacitors (GB/T 6346.3-2015/ IEC 60384-3:2006);

--- Part 3-1. Blank detail specification Surface mount (MnO2) solid electrolyte fixed capacitor rating level EZ (GB/T 6346.301-2015/IEC 60384-3-1:2006);

--- Part 4. Sub-standard solid and non-solid electrolyte aluminum capacitors (GB/T 5993-2003/IEC 60384-4:1998, Amendment No. 1..2000);

--- Part 4-1. Blank detail specification for the evaluation level of non-solid electrolyte aluminum capacitors (GB/T 5994-2003/ IEC 60384-4-1.:2000);

--- Part 4-2. Blank detail specification for solid electrolyte (MnO2) aluminum capacitors. Assessment level EZ (IEC 60384-4-2.

2007);

--- Part 5. Selection of test methods for DC mica dielectric fixed capacitors with rated voltages up to 3000 volts General requirements (GB/T 6261-1998/IEC 60384-5:1993);

--- Part 5-1. Blank detail specification Test method for DC mica dielectric fixed capacitors with rated voltage not exceeding 3000 volts Selection and general requirements assessment level E (GB/T 6262-1998/IEC 60384-5-1.:1993);

---Part 6. Sub-standard metallized polycarbonate film dielectric DC fixed capacitors (available for certification) (GB/T 14004-1992/IEC 60384-6:1987);

--- Part 6-1. Blank detail specification Metallized polycarbonate film dielectric DC fixed capacitors Assessment level E (available for certification) Use) (GB/T 14005-1992/IEC 60384-6-1. 1987);

---Part 7. Sub-standard metal foil polystyrene film dielectric DC fixed capacitors (GB/T 10185-2012);

--- Part 7-1. Blank detail specification Metal foil polystyrene film dielectric DC fixed capacitors (GB/T 10186-2012);

--- Part 8. Sub-standard Class 1 ceramic dielectric fixed capacitors (GB/T 5966-2011/IEC 60384-8:2005);

--- Part 8-1. Blank detail specification Class 1 porcelain dielectric fixed capacitor evaluation level EZ (GB/T 5967-2011/ IEC 60384-8-1:2005);

---Part 9. Sub-standard 2 types of ceramic dielectric fixed capacitors (GB/T 5968-2011/IEC 60384-9:2005);

---Part 9-1. Blank detail specification Level 2 porcelain dielectric fixed capacitor evaluation level EZ (GB/T 5969-2011/ IEC 60384-9-1:2005);

--- Part 11. Sub-standard metal foil polyethylene terephthalate film dielectric DC fixed capacitor (GB/T 6346.11-2015/IEC 60384-11:2008);

---Part 11-1. Blank detail specification metal foil polyethylene terephthalate film dielectric DC fixed capacitor Evaluation level EZ (GB/T 6346.1101-2015/IEC 60384-11-1:2008);

---Part 12. Sub-standard metal foil polycarbonate film dielectric DC fixed capacitors (IEC 60384-12:1988);

--- Part 12-1. Blank detail specification Metal foil type polycarbonate film dielectric DC fixed capacitor evaluation level EZ (IEC 60384-12-1. 1988);

---Part 13. Sub-standard metal foil polypropylene film dielectric DC fixed capacitors (GB/T 10188-2013/IEC 60384-13:2006);

--- Part 13-1. Blank detail specification Metal foil polypropylene film dielectric DC fixed capacitors Assessment level E and EZ (GB/T 10189-2013/IEC 60384-13-1:2006);

--- Part 14. Fixed capacitors for the suppression of electromagnetic interference of power supply (GB/T 6346.14-2015/IEC 60384-14.

2005);

--- Part 14-1. Blank detail specification for suppression of power supply electromagnetic interference with fixed capacitor rating level D (GB/T 6346.1401-2015/IEC 60384-14-1:2005);

--- Part 15. Sub-standard non-solid or solid electrolyte tantalum capacitors (GB/T 7213-2003/IEC 60384-15. 1982, Amendment No. 1. 1987, Amendment No. 2..1992);

---Part 15-1. Blank detail specification Non-solid electrolyte foil electrode tantalum capacitor evaluation level E (for certification) (GB/T 12794-1991/IEC 60384-15-1. 1984);

---Part 15-2. Blank detail specification for non-solid electrolyte porous anode tantalum capacitors. Assessment level E (available for certification) (GB/T 12795-1991/IEC 60384-15-2. 1984);

---Part 15-3. Blank detail specification solid electrolyte porous anode tantalum capacitor evaluation level E (for certification) (GB/T 7214-2003/IEC 60384-15-3.:1992);

---Part 16. Partially standardized metallized polypropylene film dielectric DC fixed capacitors (GB/T 10190-2012/IEC 60384-16:2005);

---Part 16-1. Blank detail specification Metallized polypropylene film dielectric DC fixed capacitors Assessment level E and EZ (GB/T 10191-2011/IEC 60384-16-1:2005);

---Part 17. Sub-standardized metallized polypropylene film dielectric AC and pulse fixed capacitors (GB/T 14579-2013/ IEC 60384-17:2005);

--- Part 17-1. Blank detail specification for metallized polypropylene film dielectric AC and pulsed fixed capacitors (GB/T 14580-2013/IEC 60384-17-1:2005);

---Part 18. Sub-standard solid (MnO2) and non-solid electrolyte sheet aluminum fixed capacitors (GB/T 17206-1998/ IEC 60384-18:1993, Amendment No. 1..1998);

---Part 18-1. Blank detail specification Surface Mount Solid (MnO2) Electrolyte Aluminum Fixed Capacitor Rating Level EZ (GB/T 17207-2012/IEC 60384-18-1:2007);

---Part 18-2. Blank detail specification for non-solid electrolyte sheet aluminum electrolyte fixed capacitors (GB/T 17208-1998/IEC 60384-18-2:1993);

---Part 19. Sub-standard surface mount metallized polyethylene terephthalate film dielectric DC fixed capacitor (GB/T 15448-2013/IEC 60384-19:2005);

---Part 19-1. Blank detail specification Surface mount metallized polyethylene terephthalate film dielectric DC fixed capacitor Rating level EZ (GB/T 16467-2013/IEC 60384-19-1:2006);

--- Part 21. Class 1 multilayer ceramic dielectric capacitors for sub-standard surface mounting (GB/T 21041-2007/IEC 60384-21:2004);

--- Part 21-1. Blank detail specification Surface-mounting class 1 multilayer ceramic dielectric fixed capacitors (GB/T 21038-2007/IEC 60384-21-1:2004);

--- Part 22. Class 2 multilayer ceramic dielectric capacitors for sub-standard surface mounting (GB/T 21042-2007/IEC 60384-22:2004);

--- Part 22-1. Blank detail specification Surface mounting type 2 multilayer ceramic dielectric fixed capacitors (GB/T 21040-2007/IEC 60384-22-1:2004);

--- Part 23. Sub-standard surface mount metallized polyethylene naphthalate film dielectric DC fixed capacitor (IEC 60384-23:2015);

--- Part 23-1. Blank detail specification Surface mount metallized polyethylene naphthalate film dielectric DC fixed capacitor Rating level EZ (IEC 60384-23-1:2015);

---Part 24. Sub-standard surface mount conductive polymer solid electrolyte fixed capacitors (IEC 60384-24:2015);

--- Part 24-1. Blank detail specification Surface mount conductive polymer solid electrolyte Fixed capacitor evaluation level EZ (IEC 60384-24-1:2006);

---Part 25. Sub-standard surface mount conductive polymer solid electrolyte aluminum fixed capacitors (GB/T 6346.25-2018/ IEC 60384-25:2015);

---Part 25-1. Blank detail specification Surface Mount Conductive Polymer Solid Electrolyte Aluminum Fixed Capacitor Rating Level EZ (GB/T 6346.2501-2018/IEC 60384-25-1:2006);

---Part 26. Sub-standard conductive polymer solid electrolyte aluminum fixed capacitors (GB/T 6346.26-2018/IEC 60384-26:2010);

---Part 26-1. Blank detail specification Conductive polymer solid electrolyte aluminum fixed capacitor evaluation level EZ This part is part 26-1 of "Fixed Capacitors for Electronic Equipment".

This part is drafted in accordance with the rules given in GB/T 1.1-2009.

This section uses the translation method equivalent to IEC 60384-26-1:2010 "Fixed capacitors for electronic equipment - Part 26-1.

Fine specification of conductive polymer solid electrolyte aluminum fixed capacitor evaluation level EZ".

The documents of our country that have a consistent correspondence with the international documents referenced in this part are as follows.

GB/T 2423.28-2005 Environmental testing for electric and electronic products - Part 2: Test methods Test T. Soldering (IEC 60068-2-20:1979, IDT)

GB/T 2693-2001 Fixed capacitors for electronic equipment - Part 1: General specification (IEC 60384-1.:1999, IDT) This section has made the following editorial changes.

--- Correction is inconsistent with the upper standard IEC 60384-26:2010. The value "6" of "p" of "C3 grouping" in Table 5 is corrected to "3", the value "24" of "n" is corrected to "36". The value "12" of "p" of "C4 grouping" in Table 5 is corrected to "6".

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 30 pages — is available in the English PDF.

How to Download GB/T 6346.2601-2018

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.