GB/T 42255-2022Procurement specification of corrosion-resisting steel solid rivets for aerospace (English PDF)
航空航天用不锈钢实心铆钉通用规范
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 42255-2022 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
December 30, 2022
Implementation date
April 1, 2023
Scope
GB/T 42255-2022 is the English-translated version of 航空航天用不锈钢实心铆钉通用规范.
GB/T 42255-2022 — This document specifies the quality assurance regulations, technical requirements, and test methods for stainless steel solid rivets used in aerospace (hereinafter referred to as "rivets").
Law, test report and certificate requirements. This document is applicable to the design, manufacture, procurement and acceptance of stainless steel solid rivets for aerospace.
Found what you need?
Document preview — GB/T 42255-2022
National Standard of the People's Republic of China
- ICS
- 49.030.99
- Classification
- V 20
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Preface
- 1 Scope1
- 2 Normative references1
- 3 Terms and Definitions1
- 4 Quality Assurance Provisions2
- 4.1 Inspection classification2
- 4.2 Inspection conditions2
- 4.3 Identification test2
- 4.4 Quality Consistency Inspection3
- 5 Technical requirements and test methods3
- 6 Test records and test reports6
- 7 Certificate of Conformity6
- Appendix A (informative) Technical differences between this document and ISO 12289.2016 and their reasons7
foreword
This document is in accordance with the provisions of GB/T 1.1-2020 "Guidelines for Standardization Work Part 1.Structure and Drafting Rules for Standardization Documents"
drafting.
This document is modified to adopt ISO 12289.2016 "Aerospace Rivets, Solid, Corrosion-resistant Steel Procurement Specifications".
Compared with ISO 12289.2016, this document has many technical differences. A vertical single line is used in the blank position on the outer page of the terms involved.
(|) are marked. See Appendix A for a list of these technical differences and their causes.
Please note that some contents of this document may refer to patents. The issuing agency of this document assumes no responsibility for identifying patents.
1 Scope
This document specifies the quality assurance regulations, technical requirements, and test methods for stainless steel solid rivets used in aerospace (hereinafter referred to as "rivets").
Law, test report and certificate requirements.
This document is applicable to the design, manufacture, procurement and acceptance of stainless steel solid rivets for aerospace.
2 Normative references
The contents of the following documents constitute the essential provisions of this document through normative references in the text. Among them, dated references
For documents, only the version corresponding to the date is applicable to this document; for undated reference documents, the latest version (including all amendments) is applicable to
this document.
GB/T 6394 Determination method for average grain size of metals
HB6444-2002 General specification for rivets
ISO 17057 Aerospace-Rivets, solid-Testmethod
3 Terms and Definitions
The following terms and definitions apply to this document.
3.1
batch
It consists of rivets of the same type, the same diameter and length, the same furnace number material, the same process and heat treatment in the same furnace.
3.2
Rivet wire sample rivetwiresample
A wire sample with a certain length cut from one end of the wire required for the production of rivets.
3.3
Rivet sample rivetsample
A sample taken at random from a batch of rivets.
3.4
crack crack
A well-defined fracture along a metal grain boundary or across grains.
3.5
hairline seam
Axially open surface imperfections.
3.6
folding lap
Surface defects formed by sharp metal corners or chips being squeezed into the fastener surface during machining.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
How to Download GB/T 42255-2022
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 6394-1986 — Metal-methods for estimating the average grain size
GB/T 6394-2002 — Metal-methods for estimating the average grain size
GB/T 6394-2017 — Determination of estimating the average grain size of metal
GB/T 42255-2022
$135.00