GB/T 38178.2-2019Hydraulic fluid power -- Mounting dimensions for single rod cylinders, 10 MPa series -- Part 2: Short-stroke series (English PDF)
液压传动 10 MPa系列单杆缸的安装尺寸 第2部分：短行程系列
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 38178.2-2019 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
October 18, 2019
Implementation date
May 1, 2020
Scope
GB/T 38178.2-2019 is the English-translated version of 液压传动 10 MPa系列单杆缸的安装尺寸 第2部分：短行程系列.
GB/T 38178.2-2019 is the Chinese standard "Hydraulic fluid power -- Mounting dimensions for single rod cylinders, 10 MPa series -- Part 2: Short-stroke series".
Its scope clause reads: This part of GB/T 38178 specifies the installation dimensions of 10MPa series short-stroke single-rod hydraulic cylinders to meet the mutual hydraulic cylinders.
Changeability requirements. This section applies to short-stroke hydraulic cylinders with a cylinder diameter of 32mm~100mm. Note 1. This section only provides basic guidelines and does not limit its technical application, allowing manufacturers to use flexibly in the design of hydraulic cylinders.
Note 2. Hydraulic cylinders that meet the requirements of this section may require sufficient installation space. Its clauses include terms and definitions; bore; piston stroke and tolerance.
Found what you need?
Document preview — GB/T 38178.2-2019
National Standard of the People's Republic of China
- ICS
- 23.100.20
- Classification
- J 20
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 bore
- 5 piston stroke and tolerance
1 Scope
This part of GB/T 38178 specifies the installation dimensions of 10MPa series short-stroke single-rod hydraulic cylinders to meet the mutual hydraulic cylinders.
Changeability requirements.
This section applies to short-stroke hydraulic cylinders with a cylinder diameter of 32mm~100mm.
Note 1. This section only provides basic guidelines and does not limit its technical application, allowing manufacturers to use flexibly in the design of hydraulic cylinders.
Note 2. Hydraulic cylinders that meet the requirements of this section may require sufficient installation space.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article.
Pieces. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 2348 fluid transmission system and component bore and piston rod diameter (GB/T 2348-2018, ISO 3320.2013,
MOD)
GB/T 2350 Hydraulic and pneumatic systems and components piston rod thread type and size series (GB/T 2350-1980, eqv
ISO 4395.1978)
GB/T 2878.1 Hydraulic drive connection with metric and stud ends for metric and O-ring seals Part 1. Port (GB/T 2878.1-2011, ISO 6149-1.2006, IDT)
GB/T 5277 fastener bolts and screw through holes (GB/T 5277-1985, eqvISO 273.1979)
GB/T 9094 hydraulic cylinder cylinder installation size and installation type code (GB/T 9094-2006, ISO 6099.2001, IDT)
GB/T 17446 fluid drive system and component vocabulary (GB/T 17446-2012, ISO 5598.2008, IDT)
ISO 1179-1 Pipe couplings for hydraulic transmission and general purpose with ISO 228-1 thread with elastomeric seal or metal to metal
Sealed port and stud end Part 1. Threaded port (Connectionsforgeneraluseandfluidpower-Portsand studendswithISO 228-1threadswithelastomericormetal-to-metalsealing-Part 1.Threadedports)
3 Terms and definitions
The terms and definitions defined in GB/T 17446 apply to this document.
4 bore
The bore should meet the requirements of GB/T 2348.
5 piston stroke and tolerance
See Table 1 for piston stroke and tolerance. […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 2348Fluid power systems and components -- Cylinder bores and piston rod diameters
- GB/T 2348-2018Fluid power systems and components -- Cylinder bores and piston rod diameters
- GB/T 2350Fluid power systems and components - Cylinder piston rod thread types and dimensions
- GB/T 2350-1980Fluid power systems and components - Cylinder piston rod thread types and dimensions
- GB/T 2878.1Connections for hydraulic fluid power - Ports with truncated housing and stud ends with metric threads - Part 1: Ports with truncated housing
- GB/T 2878.1-2011Connections for hydraulic fluid power - Ports with truncated housing and stud ends with metric threads - Part 1: Ports with truncated housing
ISO 3320.2013 · ISO 4395.1978 · ISO 6149 · ISO 6099.2001 · ISO 5598.2008 · ISO 1179 · ISO 228
How to Download GB/T 38178.2-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 17446-2024 — Fluid power systems and components - Vocabulary
GB/T 2348-2018 — Fluid power systems and components -- Cylinder bores and piston rod diameters
GB/T 2350-2020 — Fluid power systems and components - Cylinder piston rod thread types and dimensions
Secure payment via Stripe
Payments accepted
GB/T 38178.2-2019
$145.00