GB/T 37891.6-2019Cutter arbors with parallel key and tenon drive -- Part 6: Dimensions and designation of tool holders with modular taper interface with ball track system (English PDF)

Foreword

GB/T 37891 "Milling cutter with flat key and end key drive" is divided into 6 parts.

--- Part 1. General size;

--- Part 2. Dimensions and markings of hollow cone-shank shanks with flanged contact surfaces;

--- Part 3. Dimensions and markings with 7.24 automatic tool changer taper shank;

--- Part 4. Size and marking of the 7.24 manual tool changer taper shank;

--- Part 5. Dimensions and markings of multi-sided taper shank with flanged contact surfaces;

--- Part 6. Dimensions and markings of modular taper shank with steel ball tensioning system.

This part is the sixth part of GB/T 37891.

This part is drafted in accordance with the rules given in GB/T 1.1-2009.

This part uses the redrafting method to modify the ISO 10649-6.2012 milling cutter with flat key and end key drive. Part 6. Strip

The dimensions and markings of the module's tapered handle shank for the ball tensioning system.

The technical differences between this part and ISO 10649-6.2012 and their reasons are as follows.

---About the normative reference documents, this part has made technical adjustments to adapt to China's technical conditions, adjustments

The situation is reflected in Chapter 2, "Regulatory Citations", and the specific adjustments are as follows.

* Replace ISO 2768-2 with GB/T 1184 equivalent to the international standard;

* Replace ISO 2768-1 with GB/T 1804 equivalent to the international standard;

* Replace ISO 2780 with GB/T 20329 equivalent to the international standard;

* Replace ISO 26622-1 with GB/T 33524.1 equivalent to the international standard;

* Replace ISO 10649-1 with GB/T 37891.1 modified to adopt international standards;

* Replace ISO 10643 with GB/T 37895 modified to international standards.

--- Revised the drawing method of the bolt in Figure 1, the original international standard drawing method is wrong.

This standard has made the following editorial changes.

--- Removed references to international standards.

This part was proposed by the China Machinery Industry Federation.

This part is under the jurisdiction of the National Tool Standardization Technical Committee (SAC/TC91).

This section drafted by. Changzhou Haili Tools Co., Ltd., Changzhou Dinghao Precision Machinery Co., Ltd., Chengdu Tool Research Institute Co., Ltd.

1 Scope

This part of GB/T 37891 specifies the dimensions of a modular cone-shank milling cutter with a flat key and end key drive and a steel ball tensioning system.

mark.

This section applies to modular taper shank cutters with flat and end key drive and steel ball tensioning system.

2 Normative references

The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this document. For undated references, the latest edition (including all amendments) applies to this document.

GB/T 1184 Shape and position tolerances without tolerance values (GB/T 1184-1996, eqvISO 2768-2. 1989)

GB/T 1804 General tolerances No tolerances for linear and angular dimensions (GB/T 1804-2000, eqvISO 2768-1.

1989)

GB/T 20329 end-key transmission milling cutter and cutter cutter bar interchangeable size (GB/T 20329-2006, ISO 2780.

1986, IDT)

GB/T 33524.1 Module conical interface with steel ball tensioning systems - Part 1. shank dimensions and markings (GB/T 33524.1-

2017, ISO 26622-1.2008, IDT)

GB/T 37891.1 Milling shanks with flat and end key drives - Part 1. General dimensions (GB/T 37891.1-2019,

ISO 10649-1.2013, MOD)

GB/T 37895 size with flat key and end key drive milling cutter attachment (GB/T 37895-2019, ISO 10643.2009,

MOD)

3 type and size