GB/T 37474-2019Methods and requirements of airbag system abuse test for automobile (English PDF)
汽车安全气囊系统误作用试验的方法和要求
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 37474-2019 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 10, 2019
Implementation date
December 1, 2019
Scope
GB/T 37474-2019 is the English-translated version of 汽车安全气囊系统误作用试验的方法和要求.
GB/T 37474-2019 is the Chinese standard "Methods and requirements of airbag system abuse test for automobile". Its scope clause reads: This Standard specifies methods and requirements of airbag system abuse test for automobile.
This Standard is applicable to M1 vehicles which install the airbag system and have a minimum ground clearance of more than 100 mm in the state of mass in running order.
Its clauses include terms and definitions; requirements; test method. It was issued by the State Administration for Market Regulation on MAY 10, 2019 and took effect on DECEMBER 01, 2019.
Found what you need?
Document preview — GB/T 37474-2019
National Standard of the People's Republic of China
- ICS
- 43.040.60
- Classification
- T 26
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword3
- 1 Scope4
- 2 Normative references4
- 3 Terms and definitions4
- 4 Requirements5
- 5 Test method5
1 Scope
This Standard specifies methods and requirements of airbag system abuse test for automobile.
This Standard is applicable to M1 vehicles which install the airbag system and have a minimum ground clearance of more than 100 mm in the state of mass in running order.
2 Normative references
The following documents are indispensable for the application of this document.
For dated references, only the dated version applies to this document. For undated references, the latest edition (including all amendments) applies to this document.
GB/T 19949.1, Road vehicle. Airbag components. Part 1: Vocabulary
JC/T 899, Concrete curbs
3 Terms and definitions
Terms and definitions determined by GB/T 19949.1 and the following ones are applicable to this document.
3.1 Airbag system
A system that consists of one or several sensor(s), an airbag control unit, and an airbag module.
3.2 Airbag control unit
An in-vehicle control unit that controls the airbag system.
3.3 Deployment
Inflate the airbag.
3.4 Abuse
Airbag deployment that occurs not for the function of occupant protection.
3.5 Mass in running order
The whole-vehicle mass plus 75 kg.
3.6 Door and lid or bonnet
A system that consists of front and rear doors, engine cover, rear trunk lid, etc.
4 Requirements
After the tests which are specified in 5.2, 5.3, and 5.4 are completed, the airbag that is equipped in the vehicle shall not deploy.
5 Test method
5.1 Vehicle preparation
5.1.1 The test vehicle shall reflect the characteristics of the series of products and shall include all normally-installed equipment which shall be in a state of normal operation.
5.1.2 Before each test, ensure that the transmission system, suspension system (including tires), steering and braking system of the test vehicle are in the state that is specified by the vehicle manufacturer, and the engine of the vehicle is in the starting state or the ignition switch is on the position of "ON".
5.1.3 The mass of the test vehicle shall be the mass in running order.
5.2 Static test
5.2.1 Door and lid test
When the door glass is at the lowest position, close the vehicle door and lid systems one by one at a speed of lock-body position not less than 4 m/s (the speed at which the door is closed) without the use of tools. During the test, other non-test vehicle door and lid systems are closed.
For vehicles whose lock-body speed cannot reach 4 m/s at the moment of closing the door due to the special design of the door and lid system, carry out the closing test of the corresponding door and lid system at the highest closing speed that the vehicle can reach during the test.
5.2.2 Test to move the outer seat in the front row
5.3 Roadblock test (test site: dry hard road)
5.3.1 Test to pass the curb from the front side
Drive the test vehicle at a speed of 40 km/h ± 2 km/h; drive the two front-axle wheels simultaneously to a T1 curb plane-road that is 100 mm above the ground; besides, it is required that, during the test, the test vehicle shall be driven with full braking and no braking respectively once before the front plane of the test vehicle is 1 m away from the curb (see JC/T 899 for the dimensions).
5.3.2 Test to pass the wooden beam from the front side
Drive the test vehicle at a speed of 40 km/h ± 2 km/h; drive the two front-axle wheels simultaneously through a wooden beam that is fixed to the ground, of which the height above the ground is 100 mm, the width is 100 mm and the length is 2 500 mm; besides, it is required that, during the test, the test vehicle shall be driven with full braking and no braking respectively once before the front plane of the test vehicle is 1 m away from the wooden beam.
5.3.3 Test to pass the slope from the front side
Drive the test vehicle, at the speed of 40 km/h ± 2 km/h; make the two front-axle wheels through a fixed slope at a constant speed (as shown in Figure 4).
The slope is 250 mm high and 2000 mm long. in millimeters
5.4 Rough road test
5.4.1 Belgian road test
Drive the test vehicle stably at a speed of 40 km/h ± 2 km/h on the Belgian road (medium Belgian road) for at least 20 m, with full braking and no braking driving for once respectively. For the Belgian road, it is required that the cross slop is no more than 1.5%; it shall be paved by 120 mm × 250 mm stones; the height standard deviation is not more than 15 mm; the road surface is evenly concave and convex; the road features are shown in Figure 5. Driving direction of the test vehicle […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 37474-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
GB/T 37474-2019
$125.00