GB/T 325.5-2015Packing containers—Steel drums—Part 5: Non-removable head (tight head) drums with a maximum total capacity of 200L (English PDF)
包装容器 钢桶 第5部分：200L及以下闭口钢桶
This is a limited preview
Buy now to download the full PDF (15 pages)
Need quotation for your management?
Get a formal quotation for GB/T 325.5-2015 in 30 minutes.
Issued by
SAMR; SAC
Level / Type
National · Recommended
Issue date
May 15, 2015
Implementation date
January 1, 2016
Scope
GB/T 325.5-2015 is the English-translated version of 包装容器 钢桶 第5部分：200L及以下闭口钢桶.
GB/T 325.5-2015 is part 5 of GB/T 325 and specifies the structure and the dimensions of closed steel drums with a total capacity of 200 L and below; the page title renders the same object as non-removable head, or tight head, drums with a maximum total capacity of 200 L. Clause 1 says the part applies to the manufacture of such drums, and states no exclusion.
The foreword divides GB/T 325 into five parts: common technical requirements; full opening drums of minimum total capacity 208 L, 210 L and 216.5 L; closed steel drums of minimum total capacity 212 L, 216.5 L and 230 L; full opening drums of 200 L and below; and this part for closed steel drums of 200 L and below.
The body runs from scope and normative references to clause 3, which takes over the terms and definitions of GB/T 4122.4, then clause 4 on dimensions, which refers the closed drum sizes to Figure 1 and Figure 2 and the corresponding size requirements to Table 1, clause 5 on materials, which sends the drum material to GB/T 325.1 and the closure material to GB/T 13251, and clause 6 on structure, which sends the drum structure to GB/T 325.1 and the figures, deals with raised bars, rolling ring bars or corrugations on the drum body to increase strength, and places the closure on the lid as shown in the figures and in accordance with GB/T 13251.
The draft on the page stops at the end of clause 6, so nothing beyond the structure provisions is displayed. Clause 2 cites GB/T 325.1, GB/T 4122.4 and GB/T 13251.
The part is held by the National Packaging Standardization Technical Committee (SAC/TC49) and was drafted by the National Packaging Product Quality Supervision and Inspection Center (Guangzhou), the Guangzhou quality supervision and testing institute, the Jiangsu Province Product Quality Supervision and Inspection Institute and two further companies whose names the draft garbles.
It carries ICS 55.140 and Chinese classification A82, and it was issued on 15 May 2015 and has applied since 1 January 2016.
Found what you need?
Document preview — GB/T 325.5-2015
National Standard of the People's Republic of China
- ICS
- 55.140
- Classification
- A 82
Issued by: State Administration for Market Regulation; Standardization Administration of the PRC
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and Definitions
- 4 Size
- 5 Material
- 6 Structure
Foreword
GB/T 325 "containers drums" is divided into five sections.
--- Part 1. Common technical requirements;
--- Part 2. The minimum total capacity of 208L, 210L and 216.5L full opening drums;
--- Part 3. minimum total capacity of 212L, 216.5L and 230L closed steel drums;
Part --- Chapter 4.200L and below the full opening drums;
Part --- Article 5.200L closed steel drums and below.
This section GB/T 325 - Part 5.
This section drafted in accordance with GB/T 1.1-2009 given rules.
1 Scope
GB/T in this part 325 specifies the total capacity of 200L closed steel drums and below the structure and size.
This section applies to a total capacity of 200L closed steel drums and below manufacturing.
2 Normative references
The following documents for the application of this document is essential. For dated references, only the dated version suitable for use herein Member. For undated references, the latest edition (including any amendments) applies to this document.
GB/T 325.1 packaging container drums - Part 1: General technical requirements
GB/T 4122.4 Packaging Terminology - Part 4: materials and containers
GB/T 13251 Packaging drums embedded flange closure
3 Terms and Definitions
Terms and definitions GB/T 4122.4 defined apply to this document.
4 Size
Closed Cylinder dimensions shown in Figure 1, Figure 2, corresponding to the size requirements shown in Table 1.
5 Material
5.1 drums material shall comply with GB/T 325.1 in.
5.2 closure material shall comply with GB/T 13251 of.
6 Structure
6.1 drums structure should comply with GB/T 325.1, shown in Figure 1, Figure 2.
6.2 Barrel body should rise by bar or rolling ring bars, corrugated increase strength, as shown in FIG.
6.3 mounted on the lid closure position shown in FIG. 1, FIG. The closure should be consistent with GB/T 13251 regulations.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 15 pages — is available in the English PDF.
Referenced standards
Similar standards
How to Download GB/T 325.5-2015
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 13251-2018 — Packaging - Steel drum closures
GB/T 325.1-2018 — Packaging containers—Steel drums—Part 1: General specifications
GB/T 4122.4-2010 — Packaging terms - Part 4: Materials and containers
Secure payment via Stripe
Payments accepted
GB/T 325.5-2015
$85.00