GB/T 25162.2-2010Sacks -- Drop test -- Part 2: Sacks made from thermoplastic flexible film (English PDF)
包装袋 跌落试验 第2部分：热塑性软质薄膜袋
This is a limited preview
Buy now to download the full PDF (7 pages)
Need quotation for your management?
Get a formal quotation for GB/T 25162.2-2010 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
September 26, 2010
Implementation date
March 1, 2011
Scope
GB/T 25162.2-2010 is the English-translated version of 包装袋 跌落试验 第2部分：热塑性软质薄膜袋.
GB/T 25162.2-2010 — This section GB/T 25162 specifies the test side by vertical impact drop method of Full thermoplastic flexible film bag law.
This method can be used not only on the vertical impact study thermoplastic flexible film bag of single tests can also be used as a measurement of the thermoplastic soft Quality film bag containing the dangerous impact of vertical circulation system, an integral part of a series of resistance tests.
This section specifies the content of the test equipment, test procedures and test reports. This section only applies to soft thermoplastic film bags.
Found what you need?
Document preview — GB/T 25162.2-2010
National Standard of the People's Republic of China
- ICS
- 55.020
- Classification
- A 80
Issued by: Standardization Administration of China
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 4 Test Equipment
- 4.1 Lifting device
- 4.2 Support means
- 4.3 Release device
- 4.4 Impact mesa
Foreword
GB/T 25162 "bag drop test" is divided into two parts.
--- Part 1. paper bag;
--- Part 2. thermoplastic flexible film bag.
This is Part 2 GB/T 25162 of.
This part identical with ISO 7965-2:1993 "bag drop test - Part 2. thermoplastic flexible film bag" (in English).
For ease of use, this standard made the following editorial changes.
a) As used in place of a decimal point, '' '';
b) Remove the preface to the international standards;
c) a reference document by the GB/T 4857.2 instead of ISO 2233:2000.
This part of the Annex A, Annex B, Annex C is informative appendix.
This part of the National Packaging Standardization Technical Committee (SAC/TC49) and focal points.
This section drafted by. China Packaging Research & Test Center, Mechanical Science Research Institute, China Packaging Federation.
1 Scope
This section GB/T 25162 specifies the test side by vertical impact drop method of Full thermoplastic flexible film bag law. This method can be used not only on the vertical impact study thermoplastic flexible film bag of single tests can also be used as a measurement of the thermoplastic soft Quality film bag containing the dangerous impact of vertical circulation system, an integral part of a series of resistance tests.
This section specifies the content of the test equipment, test procedures and test reports.
This section only applies to soft thermoplastic film bags.
2 Normative references
The following documents contain provisions which, through GB/T 25162 in this part of the reference in terms of this section. For dated reference documents Member, all subsequent amendments (not including errata content) or revisions do not apply to this section, however, encouraged to reach under this section Parties to research agreement to use the latest versions of these documents. For undated reference documents, the latest versions apply to this section.
GB/T 4857.2 Transport packages temperature and humidity conditioning (GB/T 4857.2-2005, ISO 2233:2000, MOD) ISO 7023 bags empty bag inspection and sampling methods Principle 3 After a rigid plane above the lift bag full release of its free fall on the plane. Atmospheric conditions during the test, the drop height Degree and location of the package are pre-configured.
4 Test Equipment
Drop test equipment required in Appendix A in Fig.
4.1 Lifting device
Test samples are not damaged during lifting or release test sample.
4.2 Support means
Means for supporting the test sample prior to release should make the test sample in a predetermined position.
Supporting the test sample different methods, such as the test sample from the upper end of its lifting, or from the bottom to hold up, the impact on test samples Role circumstances vary widely. Thus supporting method test samples shall be stated in the test report.
4.3 Release device
The device should enable the test sample before releasing the whereabouts strike impact table is not touching any part of the device fall freely.
4.4 Impact mesa
It should have a certain level of quality rigid, so as not to move during the test, no deformation.
Typically, the impact should table.
a) block, its quality should be at least 50 times the most important test of the quality of the bag;
b) a flat, table height difference between any two points on the horizontal must not exceed 2mm;
c) strong, static load 10kg placed on any area of \u200b\u200b100mm2 table, the deformation should not exceed 0.1mm;
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 7 pages — is available in the English PDF.
Referenced standards
How to Download GB/T 25162.2-2010
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 25162.1-2010 — Packaging -- Sacks-test -- Part 1: Paper sacks
GB/T 4857.2-2005 — Packaging -- Basic tests for transport packages -- Part 2: Temperature and humidity conditioning
GB/T 4857.20-1992 — Packaging--Transport packages--Bump test method
Secure payment via Stripe
Payments accepted
GB/T 25162.2-2010
$145.00