Valid

GB/T 21557-2008Waste paper -- Estimation of stickies (English PDF)

废纸中胶粘物的测定

Preview PDF

This is a limited preview

Buy now to download the full PDF (6 pages)

Need quotation for your management?

Get a formal quotation for GB/T 21557-2008 in 30 minutes.

Issued by

Standardization Administration of China

Level / Type

National · Recommended

Issue date

March 24, 2008

Implementation date

October 1, 2008

Scope

GB/T 21557-2008 is the English-translated version of 废纸中胶粘物的测定.

GB/T 21557-2008 — This standard specifies the paper Stickies two methods. visual observation and image analysis. Two methods of image analysis method is a secondary Cut method. This standard applies to paper.

Found what you need?

Document preview — GB/T 21557-2008

National Standard of the People's Republic of China

ICS
85.020
Classification
Y 30

Issued by: Standardization Administration of China

Contents

  • Foreword
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Method A. visual method
  • 4.1 Principle
  • 4.2 Instruments and equipment

Foreword

This standard visual method to modify the use of ISO 15360-1:2000 "estimates adhesive material recycled pulp and plastic materials - Part 1.

Visual Inspection Law ", to modify the image analysis using the ISO 15360-2:2001" estimate recycled pulp plastic adhesive material and the second material Parts. image analysis. " this standard and ISO 15360-1:2000 and ISO 15360-2:2001 technical differences and their causes, see Appendix B, and this standard ISO 15360-1:2000 and ISO 15360-2:2001 Number of control clauses in Appendix C.

Appendix A of this standard is a normative appendix, Appendix B, Appendix C is informative appendix.

The standard proposed by China National Light Industry Council.

The standard paper by the National Standardization Technical Committee (SAC/TC141) centralized.

The standard by the China Pulp and Paper Research Institute is responsible for drafting.

1 Scope

This standard specifies the paper Stickies two methods. visual observation and image analysis. Two methods of image analysis method is a secondary Cut method.

This standard applies to paper.

2 Normative references

The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.

GB/T 740 pulp samples taken (GB/T 740-2003, ISO 7213. 1981, IDT) GB/T 741 Determination of pulp sample moisture (GB/T 741-2003, ISO 638. 1978, MOD) GB/T 2481.1 Bonded abrasives grain size composition testing and labeling - Part 1. kibble F4 ~ F220 (GB/T 2481.1-1998, eqv ISO 8486-1:1996, EQV) GB/T 5399 pulp slurry concentration measurement (GB/T 5399-2004, ISO 4119:1995, IDT) QB/T 1462 Solutions wet pulp from the laboratory (QB/T 1462-1992, eqv ISO 5236. 1979) TAPPIT541om-99 inside the cardboard binding strength (Z direction tensile)

3 Terms and Definitions

The following terms and definitions apply to this standard.

Some remain in the viscous substance screen slit laboratory screening devices, these sticky substance that adheres to the object in contact therewith.

NOTE. stickies presented at room temperature viscosity, or when the temperature rises, the pressure increases, showing viscosity when pH changes.

4 Method A. visual method

4.1 Principle

Aperture substance with certain laboratory screening equipment screening solution from the slurry after the screening to the filtrate clarification, will remain in the sieve is transferred to filter paper on. Identification of stickies, and were examined for the number and area of \u200b\u200bstickies.

4.2 Instruments and equipment

4.2.1 dissociation unit, shall comply with the provisions of QB/T 1462's.

4.2.2 laboratory screening equipment, average sieve slit width should be 100µm ± 5µm or 150µm ± 5µm, and each with an average seam slit width the wide difference should be less than 15µm. You can also use other slit width of the plate, but it should be stated in the report.

4.2.3 filter paper, qualitative medium, or fast.

4.2.4 tweezers.

4.2.5 Illumination device

4.2.5.1 source, should be applied to the determination of stickies, there is enough light intensity, to ensure that the smallest particles can see.

4.2.5.2 Lighting desk, desktop illuminance of 2500cd/m2 ~ 3000cd/m2, should avoid sunlight or any external source of direct Exposure.

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 6 pages — is available in the English PDF.

Referenced standards

How to Download GB/T 21557-2008

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Instant delivery (0–9 sec)

    Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
6 pages
Instant delivery (0–9 sec)
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 21557-2008

$125.00