GB/T 20914.5-2023Tools for pressing - Gas springs - Part 5: Safety instructions for gas springs (English PDF)
冲模 氮气弹簧 第5部分:氮气弹簧安全规范
Also coversGBT20914.5-2023
This is a limited preview
Buy now to download the full PDF (12 pages)
Need quotation for your management?
Get a formal quotation for GB/T 20914.5-2023 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
November 27, 2023
Implementation date
June 1, 2024
Scope
GB/T 20914.5-2023 is the English-translated version of 冲模 氮气弹簧 第5部分:氮气弹簧安全规范.
GB/T 20914.5-2023 — This document specifies the safety requirements and correct specifications for nitrogen gas springs for dies in accordance with ISO 11901-1, ISO 11901-3 and ISO 11901-4: correct installation method: The instructions and operating requirements in Appendix A of this document can help extend the service life of the nitrogen gas spring and ensure safe operation:
Found what you need?
Document preview — GB/T 20914.5-2023
National Standard of the People's Republic of China
- ICS
- 25.120.10
- Classification
- J 46
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- Introduction
- 1 Scope
- 2 Normative reference documents
- 3 Terms and definitions
- 4 Nitrogen spring safety protection
Foreword
This document complies with the provisions of GB/T 1.1-2020 "Standardization Work Guidelines Part 1: Structure and Drafting Rules of Standardization Documents" Drafting:
This document is Part 5 of GB/T 20914: GB/T 20914 has released the following 5 parts:
---Part 1: General specifications;
---Part 2: Accessory specifications;
---Part 3: Compact and powerful nitrogen gas spring;
---Part 4: Conformal high strength nitrogen gas spring;
---Part 5: Nitrogen gas spring safety specifications:
This document is equivalent to ISO 11901-5:2021 "Die Nitrogen Gas Spring Part 5: Safety Specifications for Nitrogen Gas Spring":
Please note that some content in this document may be subject to patents: The publisher of this document assumes no responsibility for identifying patents:
Introduction
GB/T 20914 adopts the ISO 11901 series of international standards: Each part is consistent with the international standard and is planned to be composed of 5 parts:
---Part 1: General specifications: The purpose is to unify the dimensions and specifications of general-purpose nitrogen gas springs:
---Part 2: Accessory specifications: The purpose is to unify the dimensions and specifications of standard accessories for nitrogen gas springs:
---Part 3: Compact and powerful nitrogen gas spring: The purpose is to unify the dimensions and specifications of compact and powerful nitrogen gas springs:
---Part 4: Equal-height and powerful nitrogen gas springs: The purpose is to unify the dimensions and specifications of high-strength nitrogen gas springs:
---Part 5: Nitrogen gas spring safety specifications: The purpose is to provide safe usage guidance for nitrogen gas spring users:
Die nitrogen gas spring Part 5: Safety Specifications for Nitrogen Gas Springs
1 Scope
This document specifies the safety requirements and correct specifications for nitrogen gas springs for dies in accordance with ISO 11901-1, ISO 11901-3 and ISO 11901-4:
correct installation method:
The instructions and operating requirements in Appendix A of this document can help extend the service life of the nitrogen gas spring and ensure safe operation:
2 Normative reference documents
This document has no normative references:
3 Terms and definitions
There are no terms or definitions to be defined in this document:
4 Nitrogen spring safety protection
4.1 General requirements Improper use of nitrogen gas springs may cause harm to people, equipment, molds, etc:
4:2~4:4 describe some causes of potential injuries and the operation methods of corresponding protective devices:
4.2 Uncontrolled backhaul security protection Due to factors such as mold parts or wedge jamming, the plunger rod of the nitrogen gas spring may not necessarily follow the pressure return stroke, see Figure 1: When stuck After the part is retracted, the return speed of the plunger rod will exceed the maximum allowable speed and hit the end point without restraint (the plunger rod has no punch reaction force, and the jamming parts are pushed out during the return journey), causing serious damage or failure of the nitrogen spring: To avoid this from happening, exhaust should be set up Device, when the nitrogen spring plunger rod exceeds the maximum allowable speed, it can exhaust and reduce pressure: This will reduce injuries caused by nitrogen spring parts being pushed out risks of:
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 12 pages — is available in the English PDF.
How to Download GB/T 20914.5-2023
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 20914.4-2019 — Stamping dies -- Gas springs -- Part 4: Gas spring with increased spring force and same built height
GB/T 20914.3-2019 — Stamping dies -- Gas springs -- Part 3: Gas spring with increased spring force and compact built height
GB/T 20914.2-2007 — Stamping dies -- Gas springs -- Part 2: Specification of accessories
GB/T 20914.5-2023
$240.00