GB/T 18737.2-2019Textile machinery and accessories -- Beams for winding -- Part 2: Wrapper's beams (English PDF)
纺织机械与附件 经轴 第2部分:整经轴
This is a limited preview
Buy now to download the full PDF (17 pages)
Need quotation for your management?
Get a formal quotation for GB/T 18737.2-2019 in 30 minutes.
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
December 31, 2019
Implementation date
December 31, 2019
Scope
GB/T 18737.2-2019 is the English-translated version of 纺织机械与附件 经轴 第2部分:整经轴.
GB/T 18737.2-2019 is the Chinese standard "Textile machinery and accessories -- Beams for winding -- Part 2: Wrapper's beams".
Its scope clause reads: This part of GB/T 18737 specifies the main dimensions, mechanical strength, shape and position tolerances of warping beams, as well as warping beams with and without shafts Drive structure and markings for warping beams.
This section applies to ordinary warping beams used in the production of grey fabrics, and is not applicable to dyeing warping beams. Its clauses include types and main dimensions.
Found what you need?
Document preview — GB/T 18737.2-2019
National Standard of the People's Republic of China
- ICS
- 59.120.20
- Classification
- W 94
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
1 Scope
This part of GB/T 18737 specifies the main dimensions, mechanical strength, shape and position tolerances of warping beams, as well as warping beams with and without shafts
Drive structure and markings for warping beams.
This section applies to ordinary warping beams used in the production of grey fabrics, and is not applicable to dyeing warping beams.
2 Normative references
The following documents are essential for the application of this document. For dated references, only the dated version applies to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
GB/T 9239.1 Mechanical vibration constant state (rigid) rotor balance quality requirements Part 1. Specification and balance tolerance test (GB/T 9239.1-2006, ISO 1940-1..2003, IDT)
GB/T 18737.8 Definition and measurement method of warp beam runout tolerance for textile machinery and accessories (GB/T 18737.8-2009, (ISO 8116-8..19951), IDT)
ISO 286-2 ISO Series Limits and Fits Part 2. Standard Tolerance Classes and Hole and Shaft Limit Deviation Tables (ISO system of limitsandfits-Part 2. Tables ofstandardtolerancegradesandlimitdeviationsforholesandshafts)
ISO 8116-4 Textile machinery and accessories Warm beams Quality class chineryandaccessories-Beamsforwinding-Part 4. Testmethodsandqualityclassificationofflanges forweaver'sbeams, warper'sbeamsand sectionalbeams)
3 types and main dimensions
The warp beam is divided into the following three types.
--- A warping beam with shaft extension;
--- B warping shaft with shaft hole centering and key transmission;
--- C warping beam with cone centering and transmission.
- C1. 50 teeth (not recommended);
- C2. 72 teeth;
- C3. 50 teeth.
The main dimensions of A and B warping beams are shown in Figures 1 and 2. The main dimensions of the C-type warp beam are shown in Figure 3.
The main dimensions of type A and B warp beams should conform to Table 1. The main dimensions of C-type warp beams should conform to Table 2.
1) ISO 8116-8..1995 has been repealed.
FZ/T 93048.1 | FZ/T 93019 | GB/T 18737.5 | GB/T 18737.3 | GB/T 18737.7 | […]
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 17 pages — is available in the English PDF.
Referenced standards
Normative references
- GB/T 9239.1Mechanical vibration—Rotor balancing—Part 1:Introduction
- GB/T 9239.1-2006Mechanical vibration—Rotor balancing—Part 1:Introduction
- GB/T 18737.8Textile machinery and accessories -- Beams for winding -- Part 8: Definitions of run-out tolerances and methods of measurement
- GB/T 18737.8-2009Textile machinery and accessories -- Beams for winding -- Part 8: Definitions of run-out tolerances and methods of measurement
ISO 1940 · ISO 8116 · ISO 286
How to Download GB/T 18737.2-2019
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Fast delivery
After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 18737.8-2009 — Textile machinery and accessories -- Beams for winding -- Part 8: Definitions of run-out tolerances and methods of measurement
GB/T 9239.1-2006 — Mechanical vibration -- Balance quality requirements for rotors in a constant (rigid) state -- Part 1: Specification and verification of balance tolerances
GB/T 9239.1-2026 — Mechanical vibration—Rotor balancing—Part 1:Introduction
GB/T 18737.2-2019
$165.00