Valid

GB/T 18310.27-2026Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-27: Tests - Dust (laminar flow) (English PDF)

纤维光学互连器件和无源器件 基本试验和测量程序 第2-27部分:试验 灰尘(层流)

Preview PDF

This is a limited preview

Buy now to download the full PDF (9 pages)

Need quotation for your management?

Get a formal quotation for GB/T 18310.27-2026 in 30 minutes.

Issued by

State Administration for Market Regulation

Level / Type

National · Recommended

Issue date

July 30, 2026

Implementation date

February 1, 2027

Scope

GB/T 18310.27-2026 is the English-translated version of 纤维光学互连器件和无源器件 基本试验和测量程序 第2-27部分:试验 灰尘(层流).

GB/T 18310.27-2026 is a test method for fibre optic interconnecting devices and passive components, covering the dust (laminar flow) test. It belongs to the GB/T 18310 series of basic test and measurement procedures, which follows the IEC 61300 series.

The document is organised around a test chamber, the dust itself and optical measurement equipment, followed by procedures: preparing and installing the device under test, initial inspection and measurements, monitoring optical performance, initial dust exposure, high temperature regulation, dust exposure, recovery and final inspection.

It also sets out severity levels and the details to be given in regulations and reports. Issued on 30 July 2026 and applicable from 1 February 2027, it does not replace an earlier edition.

Found what you need?

Document preview — GB/T 18310.27-2026

National Standard of the People's Republic of China

ICS
33.180.20
Classification
L 50

Issued by: State Administration for Market Regulation

Contents

  • Foreword
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 General Rules
  • 5.1 Test Chamber
  • 5.2 Dust
  • 5.3 Optical Measurement Equipment
  • 6 Procedures
  • 6.1 DUT Preparation
  • 6.2 Preprocessing
  • 6.3 DUT Installation
  • 6.4 Initial Inspection and Measurements
  • 6.5 Monitoring of optical performance
  • 6.6 Initial Dust Exposure
  • 6.7 High Temperature Regulation
  • 6.8 Dust exposure
  • 6.9 Recovery
  • 6.10 Final Inspection and Measurement
  • 7 Severity Level
  • 8 Details of regulations and reporting
  • References

Introduction

Fiber optic interconnects and passive devices play a vital role in fiber optic products and applications. With the advancement of optical communication technology and manufacturing... With the continuous emergence of new products, testing and measurement technologies for fiber optic interconnects and passive devices have also developed rapidly. To improve product testing and measurement procedures... To promote international coordination and trade, the IEC has developed and published the IEC 61300 series of test and measurement procedures standards to date.

It covers the measurement and testing of optical performance, mechanical properties, and environmental adaptability of fiber optic interconnects and passive devices, and is an internationally recognized... Basic standards for the inspection and acceptance of internal support products. my country has established a standard system for testing and measurement procedures for fiber optic interconnect devices and passive devices, referencing the IEC 61300 series standards.

Including GB/T 18309 "Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices Part 1: General Principles and Guidelines", GB/T 18310 "Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices - Part 2: Tests" and GB/T 18311 "Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices, Part 3: Inspection and Measurement" aims to establish product specifications.

It provides a complete and unified set of methodologies and standards for product testing and verification.

GB/T 18310 is proposed to consist of the following parts.

--Part 2-1.Test Vibrations (Sine). The purpose is to determine the test procedure for vibrations (sine).

--Part 2-2.Testing Mating Durability. The purpose is to determine the testing procedures for mating durability.

--Part 2-4.Testing the Holding Force of Optical Fibers/Cables. The purpose is to determine the test procedures for the holding force of optical fibers/cables.

--Part 2-5.Torsion Testing. The purpose is to determine the testing procedure for torsion.

--Part 2-7.Test Bending Moment. The purpose is to determine the test procedure for bending moment.

--Part 2-9.Test Impact. The purpose is to determine the test procedure for impact.

--Part 2-10.Testing for resistance to compression and load. The purpose is to determine the testing procedures for resistance to compression and load.

--Part 2-11.Testing Axial Compression. The purpose is to determine the test procedure for axial compression.

--Part 2-12.Impact Testing. The purpose is to determine the impact testing procedure.

--Part 2-14.Testing High Optical Power. The purpose is to determine the testing procedure for high optical power.

--Part 2-15.Testing the Torsional Strength of the Locking Mechanism. The purpose is to determine the test procedure for the torsional strength of the locking mechanism.

--Part 2-17.Testing at Low Temperatures. The purpose is to determine the testing procedures for low temperatures.

--Part 2-18.Dry Heat Test. The purpose is to determine the test procedure for dry heat.

--Part 2-19.Testing under constant humidity and heat. The purpose is to determine the testing procedure for constant humidity and heat.

--Part 2-21.Test Temperature-Humidity Combination Cyclic Test. The purpose is to determine the test procedure for the temperature-humidity combination cycle.

--Part 2-22.Testing Temperature Changes. The purpose is to determine the testing procedures for temperature changes.

--Part 2-23.Testing the seal of non-pressurized junction boxes. The purpose is to determine the testing procedure for the seal of non-pressurized junction boxes.

--Part 2-24.Screening test of open ceramic centering sleeve by applying stress. The purpose is to determine the stress applied... Test procedure for screening open-type ceramic centering sleeves under stress.

--Part 2-26.Salt Spray Test. The purpose is to determine the salt spray test procedure.

--Part 2-27.Test Dust (Laminar Flow). The purpose is to determine the test procedures for dust (laminar flow).

--Part 2-28.Testing Corrosive Atmospheres (Sulfur Dioxide). The purpose is to determine the testing methods for corrosive atmospheres (sulfur dioxide). program.

--Part 2-33.Assembly and disassembly of experimental mechanical connectors, fiber optic management systems, and protective enclosures. The purpose is to determine the appropriate... Test procedures for product assembly and disassembly.

--Part 2-34.Testing for resistance to solvents and contaminated liquids. The purpose is to determine the testing procedures for resistance to solvents and contaminated liquids.

--Part 2-35.Testing Fiber Optic Cable Nullification. The purpose is to determine the testing procedure for fiber optic cable nutation.

--Part 2-37.Testing fiber optic cable bending in protective enclosures and rugged connectors. The purpose is to determine the fiber optic cable bending characteristics of protective enclosures and rugged connectors. Optical cable bending test procedure for connectors.

--Part 2-38.Testing the sealing of pressure-sealed protective cases and ruggedized optical connectors. The purpose is to determine the appropriate devices. The sealing test procedure.

--Part 2-39.Tests for sensitivity to external magnetic fields. The purpose is to determine the test procedures for sensitivity to external magnetic fields.

--Part 2-40.Screening test for attenuation of single-mode adjustable-angle optical connectors. The purpose is to determine the appropriate optical connector. Screening test procedure for device attenuation.

--Part 2-41.Screening Tests for Attenuation of Single-Mode Adjustable Angle-Free Optical Connectors. The aim is to determine the appropriate optical connector... Screening test procedure for device attenuation.

--Part 2-42.Static Lateral Loading of the Test Strain Relief Mechanism. The purpose is to determine the static lateral load of the strain relief mechanism. Load test procedure.

--Part 2-43.Screening Tests for Return Loss of Test Single-Mode Physical Contact (PC) Optical Connectors. The aim is to determine the appropriate return loss... Screening test procedure for return loss of optical connectors.

--Part 2-44.Testing the flexure of stress relief devices. The purpose is to determine the flexure testing procedure for stress relief devices.

--Part 2-45.Testing for water immersion durability. The purpose is to determine the test procedures for water immersion durability.

--Part 2-47.Testing for Temperature Shock. The purpose is to determine the testing procedures for temperature shock.

--Part 2-48.Test Temperature and Humidity Cycling. The purpose is to determine the test procedure for temperature and humidity cycling.

--Part 2-49.Test Connector Installation Test. The purpose is to determine the test procedure for connector installation.

--Part 2-50.Screening Tests for Optical Connectors under Static Load. The purpose is to determine the screening performance of optical connectors under static load. Screening test procedures.

--Part 2-51.Transmission characteristics of test optical connectors under tensile load. The purpose is to determine the transmission characteristics of optical connectors under tensile load. Transmission characteristic test procedure.

--Part 2-54.Testing Corrosive Atmospheres (Gas Mixtures). The purpose is to determine the testing methods for corrosive atmospheres (gas mixtures). program.

--Part 2-55.Testing the Installation Strength of the Adapter. The purpose is to determine the testing procedure for the installation strength of the adapter.

--Part 2-56.Testing the wind resistance of the installed wiring box. The purpose is to determine the wind resistance of the installed wiring box. Verification procedure.

1 Scope

This document describes the test methods for dust (laminar flow) in fiber optic interconnects and passive devices.

2 Normative references

The contents of the following documents, through normative references within the text, constitute essential provisions of this document. Dated citations are listed below. This document.

IEC 61300-1 Basic test and measurement procedures for fiber optic interconnects and passive devices - Part 1: General principles and guidelines (Fibre optic interconnecting devices and passive components-Basic test and measurement procedures- Part 1: General and guidance)

Note: GB/T 18309.1-2001 Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices Part 1: General Principles and Guidelines (IEC 61300-1:1995, IDT)

IEC 61300-3-1 Fiber optic interconnects and passive devices - Basic test and measurement procedures - Part 3-1.Inspection and measurement Visual inspection (Fibre optic interconnecting devices and passive components - Basic test and measurement)

Note: GB/T 18311.1-2003 Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices Part 3-1.Inspection and Measurement of External Components Visual inspection (IEC 61300-3-1:1995, IDT)

IEC 61300-3-3 Fiber optic interconnects and passive devices - Basic test and measurement procedures - Part 3-3.Inspection and measurement Dynamic monitoring of changes in signal attenuation and return loss (Fibre optic interconnecting devices and passive components-Ba-sic test and measurement procedures-Part 3 - 3:Examinations and measurements-Active monitoring of changes in attenuation and return loss)

Note: GB/T 18311.3-2001 Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices - Part 3-3.Inspection and Measurement Measurement of attenuation and return loss changes (multi-channel) (IEC 61300-3-3:1997, IDT)

IEC 61300-3-4 Fiber Optic Interconnects and Passive Devices - Basic Test and Measurement Procedures - Part 3-4.Inspection and Measurement Attenuation (Fibre optic interconnecting devices and passive components-Basic test and measurement procedure-dures-Part 3-4.Examinations and measurements-Attenuation) Subtraction (IEC 61300-3-4:2001, IDT)

IEC 61300-3-6 Fiber optic interconnects and passive devices - Basic test and measurement procedures - Part 3-6.Inspection and measurement Measure return loss (Fibre optic interconnecting devices and passive components - Basic test and measurement)

Note: GB/T 18311.6-2001 Basic Test and Measurement Procedures for Fiber Optic Interconnects and Passive Devices - Part 3-6.Inspection and Measurement Wave loss (IEC 61300-3-6:1997, IDT)

IEC 61300-3-35 Fiber optic interconnects and passive devices - Basic test and measurement procedures - Part 3-35.Inspection and measurement

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 9 pages — is available in the English PDF.

Referenced standards

Normative references

IEC 61300-1 · IEC 61300-3-1 · IEC 61300-3-3 · IEC 61300-3-4 · IEC 61300-3-6 · IEC 61300-3-35

How to Download GB/T 18310.27-2026

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
9 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 18310.27-2026

$255.00