GB/T 17737.317-2018Coaxial communication cables -- Part 1-317: Mechanical test methods -- Test for crush resistance of cable (English PDF)
Also coversGBT17737.317-2018
Open the GB/T 17737.317-2018 preview as PDF
This is a limited preview
Buy now to download the full PDF
Issued by
State Administration for Market Regulation, China National Standardization Administration
Level / Type
National · Recommended
Issue date
March 15, 2018
Implementation date
October 1, 2018
Scope
GB/T 17737.317-2018 (Coaxial communication cables -- Part 1-317: Mechanical test methods -- Test for crush resistance of cable) is available as an English-translated PDF.
GB/T 17737.317-2018 — This part of GB/T 17737 applies to coaxial communication cables. It specifies the test method for determining the compression resistance of a coaxial cable.
Document preview — GB/T 17737.317-2018
National Standard of the People's Republic of China
- ICS
- 33.120.10
- Classification
- L 26
Issued by: State Administration for Market Regulation, China National Standardization Administration
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 test methods
- 4.1 Test device
- 4.2 Samples
- 4.3 Procedures
Foreword
GB/T 17737 "Coaxial Communication Cable" has or plans to issue the following parts.
--- Part 1. General rules, definitions and requirements;
--- Section 1-31 . Mechanical test methods ; Ellipticity test ;
-- Part 1-302 . Mechanical test methods ; eccentricity test ;
-- Part 1-304 . Mechanical test methods ; Impact test ;
Part 1-108 . Mechanical test methods -- Tensile strength and elongation test of copper clad metal ;
--- Part 1-310. Mechanical test methods Torsional characteristics of copper clad metal;
--- Part 1-313. Mechanical test methods Adhesion of media and sheath;
--- Part 1-314. Mechanical test methods Bending test of cables;
--- Part 1-316. Mechanical test methods Maximum tensile strength test of cables;
--- Part 1-317. Mechanical test methods Cable compression test;
--- Sections 1-318. Mechanical test methods Thermal performance test;
--- Part 1-324 . Mechanical test methods Cable abrasion resistance test ;
--- Part 1-325 . Mechanical test methods Wind - induced vibration test ;
This part is part 1-317 of GB/T 17737.
This section was drafted in accordance with the rules given in GB/T 1.1-2009.
This section uses the translation method identical to the use of IEC 61196-1-317.2006 "coaxial communication cable part 1-317. mechanical test side
Method Cable Compression Test.
The Chinese documents that have a consistent correspondence with the normatively quoted international documents in this section are as follows.
---GB/T 17737.1-2013 Coaxial telecommunication cables Part 1. General specifications General, definitions and requirements (IEC 61196-1.
2005, IDT).
1 Scope
This part of GB/T 17737 applies to coaxial communication cables. It specifies the test method for determining the compression resistance of a coaxial cable.
2 Normative references
The following documents are indispensable for the application of this document. For dated references, only dated versions apply to this article
Pieces. For undated references, the latest version (including all amendments) applies to this document.
IEC 61196-1 Coaxial Communication Cables Part 1. Generic Specification General, Definitions and Requirements (Coaxialcommunicationca-
bles-Part 1.Generic specification-General,definitionsandrequirements)
3 Terms and definitions
The terms and definitions defined by IEC 61196-1 apply to this document.
4 test methods
4.1 Test device
The test device enables the cable to be tested to be pressed between a flat steel base plate and a movable steel plate and applied to a 100 mm long test cable
The force should be uniform.
The edge of the movable plate should be rounded with a radius of 5mm. The rounded edges are not contained within the 100mm flat section. Suitable test
The device is shown in Figure 1.
4.2 Samples
The sample should be of sufficient length for the specified test.
Except as otherwise specified in relevant sub-standards or detailed specifications, the test temperature of the tested cable shall be maintained at 15°C~35°C.
For cables with an outside diameter of less than 5mm, the tested cable can be tested in a loop. In this case, the applied force is the specified value
Twice. The radius of the ring should be large enough to not affect the transmission characteristics of the cable.
4.3 Procedures
The cable under test shall be mounted on the base plate of the test device to prevent lateral sliding. Use a rounded parallel plate to move on the test
Apply a pressure load on the cable. The load should be applied gradually or stepwise to the value (F) specified in the relevant sub-specification or detail specification. There should be no
Sudden change. The maximum load should last 2min. After removing the load, the cable under test can be restored for 2 minutes. If step loading, step load ratio
Should not exceed 1.5.1.
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.
Referenced standards
Normative references
IEC 61196
How to Buy GB/T 17737.317-2018
- 1Add to cart. Click the "Buy GB/T 17737.317-2018" button on this page. You can add more standards before checkout.
- 2Checkout. Enter your email and billing details. Payment is processed securely by Stripe (cards, Apple Pay, Google Pay supported).
- 3Instant delivery (0–9 sec). Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4Invoice included. A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 17737.100-2018 — Coaxial communication cables -- Part 1-100: Electrical test methods -- General requirements
GB/T 17737.101-2018 — Coaxial communication cables -- Part 1-101: Electrical test methods -- Test for conductor d.c. resistance of cable
GB/T 17737.102-2018 — Coaxial communication cables -- Part 1-102: Electrical test methods -- Test for insulation resistance of cable dielectric
Secure payment via Stripe
Payments accepted
GB/T 17737.317-2018
$70.00