Valid

GB/T 16515-2023Potentiometers for use in electronic equipment - Part 5: Sectional specification - Single-turn rotary low-power wire wound and non-wire wound potentiometers (English PDF)

电子设备用电位器第5部分:分规范单圈旋转低功率线绕和非线绕电位器

Preview PDF

This is a limited preview

Buy now to download the full PDF (24 pages)

Need quotation for your management?

Get a formal quotation for GB/T 16515-2023 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

September 7, 2023

Implementation date

January 1, 2024

Scope

GB/T 16515-2023 is the English-translated version of 电子设备用电位器第5部分:分规范单圈旋转低功率线绕和非线绕电位器.

GB/T 16515-2023 is the Chinese standard "Potentiometers for use in electronic equipment - Part 5: Sectional specification - Single-turn rotary low-power wire wound and non-wire wound potentiometers".

Its scope clause reads: This document applies to single-turn low-power wirewound and non-wirewound potentiometers (hereinafter referred to as "potentiometers") with a rated power consumption not exceeding 10W.

These potentiometers are mainly used in electronic equipment. This document specifies the preferred ratings and characteristics of potentiometers and selects applicable quality assessment procedures from IEC 60393-1.2008, Test and measurement methods, and give the general performance requirements for this type of potentiometers.

This document gives the minimum performance requirements and minimum test severity levels. Its clauses include normative reference documents; terms and definitions.

Found what you need?

Document preview — GB/T 16515-2023

National Standard of the People's Republic of China

ICS: 31.040.20
Classification: L 14
Replacing: GB/T 16515-1996

Issued by: State Administration for Market Regulation, China National Standardization Administration

Preface
Introduction
1 Scope
2 Normative reference documents
3 Terms and Definitions
4 What should be given in the detailed specification
4.1 General
4.2 Outline drawing and dimensions
4.3 Installation
4.4 Variety
4.5 Resistance Law
4.6 Ratings and Characteristics
4.7 Flag
4.8 Ordering information
4.9 Additional information
4.10 Flag
5 Priority characteristics, ratings and test severity level
5.1 Priority Features
5.2 Priority rating
5.3 Priority test severity level
6 Quality Assessment Procedure
6.1 Overview
6.2 Definition
6.3 Approval
6.4 Quality consistency inspection
6.5 Backorder
Appendix A (Normative) Sealing test method

1 Scope

This document applies to single-turn low-power wirewound and non-wirewound potentiometers (hereinafter referred to as "potentiometers") with a rated power consumption not exceeding 10W.

These potentiometers are mainly used in electronic equipment.

This document specifies the preferred ratings and characteristics of potentiometers and selects applicable quality assessment procedures from IEC 60393-1.2008,

Test and measurement methods, and give the general performance requirements for this type of potentiometers.

This document gives the minimum performance requirements and minimum test severity levels.

2 Normative reference documents

The contents of the following documents constitute essential provisions of this document through normative references in the text. Among them, the dated quotations

For undated referenced documents, only the version corresponding to that date applies to this document; for undated referenced documents, the latest version (including all amendments) applies to this document.

GB/T 2421-2020 Environmental Testing Overview and Guidelines (IEC 60068-1.2013,IDT)

Note. GB/T 2691-2016 Marking codes for resistors and capacitors (IEC 60062.2004, IDT)

GB/T 2423.1-2008 Environmental testing of electrical and electronic products Part 1.Test methods Test A. Low temperature (IEC 60068-2-

1.2007,IDT)

GB/T 2423.2-2008 Environmental testing of electrical and electronic products Part 2.Test methods Test B. High temperature (IEC 60068-2-

2.2007,IDT)

Note. GB/T 15298-1994 Potentiometers for electronic equipment Part 1.General specifications (IEC 60393-1.1989, IDT)

IEC 60915 Capacitors and resistors for electronic equipment Dimensions of shaft ends and bushings for shaft control electronic components mounted on single-hole bushings

Note. GB/T 2775-2016 Preferred dimensions for shaft ends, shaft sleeves and single-hole shaft sleeve installation of capacitors and resistors for electronic equipment and shaft digging of electronic components (IEC 60915.2006,IDT)

IEC 61193-2.2007 Quality assessment system Part 2.Selection of sampling plans for electronic components and packaging (Qualityas- andpackages)

3 Terms and definitions

There are no terms or definitions to be defined in this document.

GB/T 6346.14 | GB/Z 40842 | SJ/T 10410 | GB/T 42308 | GB/T 40562 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 24 pages — is available in the English PDF.

Referenced standards

Normative references

IEC 60915 · IEC 61193-2:2007

How to Download GB/T 16515-2023

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.