Valid

GB/T 15579.14-2021Arc welding equipment - Part 14: Calibration, validation and consistency testing (English PDF)

弧焊设备 第14部分:校准、确认和一致性试验

Preview PDF

This is a limited preview

Buy now to download the full PDF (45 pages)

Need quotation for your management?

Get a formal quotation for GB/T 15579.14-2021 in 30 minutes.

Issued by

State Administration for Market Regulation, China National Standardization Administration

Level / Type

National · Recommended

Issue date

December 31, 2021

Implementation date

July 1, 2022

Scope

GB/T 15579.14-2021 is the English-translated version of 弧焊设备 第14部分:校准、确认和一致性试验.

GB/T 15579.14-2021 is the Chinese standard "Arc welding equipment - Part 14: Calibration, validation and consistency testing".

Its scope clause reads: This document specifies the qualification requirements for arc welding and its external monitoring equipment: This document also applies to the actual verification operation of arc welding equipment: This document may be used for installation and at such other times or intervals as the user deems appropriate to ensure that the equipment can be Other specifications that the user deems applicable: This document does not apply to: --- Plasma systems for cutting and gouging; --- arc ignition and arc stabilization device; ---Arc welding equipment designed according to IEC 60974-6: Note 1: Other components in the welding system, such as robots, rotating devices, gas circuit devices, etc:, also have an impact on the welding results, and can be verified if necessary: See ISO 17662: Note 2: Periodic inspection and testing of arc welding equipment are described in IEC 60974-4: This document is intended for users, service shops or manufacturers: it can: --- stand-alone use; --- used in conjunction with the manufacturer's instructions; or --- As the basis for the manufacturer to develop an equivalence verification program for a specific device:. Its clauses include terms and definitions.

Found what you need?

Document preview — GB/T 15579.14-2021

National Standard of the People's Republic of China

Classification
J 64

Issued by: State Administration for Market Regulation, China National Standardization Administration

Contents

  • Preface
  • Introduction
  • 1 Scope
  • 2 Normative references
  • 3 Terms and Definitions
  • 4 Safety measures
  • 5 Testers
  • 6 Verification Accuracy - Allowed Deviation
  • 7 Arc welding power source
  • 8 Wire feeder
  • 9 Verification frequency
  • 10 Marking and Verification Report
  • Appendix A (Informative) Verification Accuracy Figure
  • Appendix B (Informative) Composition of Measurements
  • Appendix C (Informative) Slope, Pulse and Synchronization Control
  • Appendix D (Informative) Precautions for TIG Welding Equipment
  • Appendix E (Informative) Sample Verification Report

1 Scope

This document specifies the qualification requirements for arc welding and its external monitoring equipment: This document also applies to the actual verification operation of arc welding equipment:

This document may be used for installation and at such other times or intervals as the user deems appropriate to ensure that the equipment can be

Other specifications that the user deems applicable:

This document does not apply to:

--- Plasma systems for cutting and gouging;

--- arc ignition and arc stabilization device;

---Arc welding equipment designed according to IEC 60974-6:

Note 1: Other components in the welding system, such as robots, rotating devices, gas circuit devices, etc:, also have an impact on the welding results, and can be verified if necessary:

See ISO 17662:

Note 2: Periodic inspection and testing of arc welding equipment are described in IEC 60974-4:

This document is intended for users, service shops or manufacturers: it can:

--- stand-alone use;

--- used in conjunction with the manufacturer's instructions; or

--- As the basis for the manufacturer to develop an equivalence verification program for a specific device:

2 Normative references

The contents of the following documents constitute essential provisions of this document through normative references in the text: Among them, dated citations documents, only the version corresponding to that date applies to this document; for undated references, the latest edition (including all amendments) applies to this document:

IEC 60974-1:2017 Arc Welding Equipment Part 1: Welding Power Source (Arcweldingequipment-Part 1:Welding powersources)

3 Terms and Definitions

The following terms and definitions apply to this document:

ISO and IEC publish terminology databases for standardization at:

---IEC Electronic Encyclopedia: http://www:electropedia:org/

---ISO online browsing platform: http://www:iso:org/obp

3:1 display value displayedvalue

A value measured by an internal instrument and displayed on the device:

NOTE: In some cases, the same display can be used for setpoints and measurements: In this case, the displayed value is usually visible during welding:

GB/T 41861 | GB/T 40337 | CNCA C06-01 | GB/T 15579.9 | GB/T 15579.6 | GB/T 15579.12 | […]

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 45 pages — is available in the English PDF.

Referenced standards

Normative references

IEC 60974

How to Download GB/T 15579.14-2021

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
45 pages
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB/T 15579.14-2021

$360.00