Valid

GB/T 14536.15-2022Automatic electrical controls—Part 15: Particular requirements for humidity sensing control (English PDF)

电自动控制器第15部分：湿度敏感控制器的特殊要求

Preview PDF

Also coversGBT14536.15-2022

This is a limited preview

Buy now to download the full PDF

Need quotation for your management?

Get a formal quotation for GB/T 14536.15-2022 in 30 minutes.

Issued by

State Administration for Market Regulation; Standardization Administration of China

Level / Type

National · Recommended

Issue date

December 30, 2022

Implementation date

July 1, 2023

Scope

GB/T 14536.15-2022 is the English-translated version of 电自动控制器第15部分：湿度敏感控制器的特殊要求.

GB 14536.1 of the chapter is applicable except as follows.

Found what you need?

Document preview — GB/T 14536.15-2022

National Standard of the People's Republic of China

ICS: 97.120
Classification: K32

Issued by: State Administration for Market Regulation; Standardization Administration of China

1 Scope and normative references1
2 Definitions1
3 General requirements1
4 General notes1
Rating 15
6 Category1
7 Profile2
8 Protection against electric shock2
9 ground protection measures2
10 Terminals and terminations2
11 structural requirements2
12 moisture and dust2
13 Electric strength and insulation resistance2
14 Fever2
15 Manufacturing deviation and drift2

Foreword

All technical content in this section is mandatory.

GB 14536 "Household and similar electrical automatic controller" is divided into two parts.

--- Part 1.General requirements;

--- Part 2.Particular requirements.

Special requirements and consists of the following components.

--- GB 14536.3 - Particular requirements for thermal motor protectors (IEC 60730-2-2, IDT);

--- Particular requirements GB 14536.4 tubular fluorescent lamp ballasts for thermal protectors (IEC 60730-2-3, IDT);

--- GB 14536.5 sealed and semi-hermetic motor - compressor motor thermal protection Particular requirements (IEC 60730-2-4,

IDT);

--- Particular requirements GB 14536.6 automatic electrical burner control systems (IEC 60730-2-5, IDT);

--- GB 14536.7 pressure sensitive electrical controls - Particular requirements (idt IEC 60730-2-6);

--- GB 14536.8 Particular requirements for timers and time switches (idt IEC 60730-2-7);

--- GB 14536.9 Particular requirements for electrically operated water valves (including mechanical requirements) (IEC 60730-2-8, IDT);

--- GB 14536.10 - Particular requirements for temperature sensing controls (IEC 60730-2-9, IDT);

--- GB 14536.11 Particular requirements for motor starting relays (IEC 60730-2-10, IDT) used;

--- GB 14536.12 Particular requirements for energy regulators (idt IEC 60730-2-11);

--- GB 14536.13 Particular requirements for electrically operated door locks (IEC 60730-2-12, IDT);

--- GB 14536.15 Particular requirements for humidity sensing controls (IEC 60730-2-13, IDT);

--- GB 14536.16 Particular requirements for electric actuators (idt IEC 60730-2-14);

--- GB 14536.17 special requirements of the float or electrode-sensitive automatic electrical water level sensing controller used in the boiler appliance

(IEC 60730-2-15, IDT);

--- GB 14536.18 - Particular requirements for household and similar use of the float type level controllers (IEC 60730-2-16, IDT);

--- GB 14536.19 Particular requirements for electrically operated gas valves, including mechanical requirements (IEC 60730-2-17, IDT);

--- GB 14536.20 Particular requirements for water and air flow sensing controls, including mechanical requirements (IEC 60730-2-18, IDT);

--- GB 14536.21 Particular requirements for electrically operated oil valves, including mechanical requirements (IEC 60730-2-19, IDT);

This section identical with IEC 60730-2-13.2006 "special for household and similar use automatic controller to humidity sensing controls

begging".

Part of this structure with IEC 60730-2-13.2006 same. In this section, there is a corresponding national standards, national standards incorporated by reference

Quasi; no national standards, IEC standards are incorporated by reference outlined.

For ease of use, this section made the following editorial changes.

a) instead of as a decimal by decimal comma ",". ",";

b) increase the national standard foreword;

c) with the "GB 14536.1" instead of "Part 1."

This part of GB 14536.1-2008 "Household and similar electrical controls - Part 1.General requirements" in conjunction.

This Part replaces GB 14536.15-1999 "Household and similar electrical controls - Particular requirements for humidity sensing controls."

Compared with GB 14536.15-1999 part of the main changes are as follows.

a) Chapter 7 in Table 7.2 has some changes;

GB 14536.15-2008/IEC 60730-2-13.2006

b) Chapter 15 Manufacturing deviation and drift representation has increased;

c) the name of several sections according to changes GB 14536.1 made the appropriate changes;

d) Appendix H (requires electronic control) made major changes.

Appendix H and Appendix AA This section is normative appendix.

This part is proposed by the China Electrical Equipment Industrial Association.

This part of the National Standardization Technical Committee household automatic control (SAC/TC212) centralized.

This section is drafted. Guangzhou CVC Testing Institute, Guangzhou Electric Apparatus Research Institute, Zhejiang Yan Thermostat Co., Ltd. Ningbo

Economic and Technological Development Zone Haixin Electric Technology Co., Ltd., Guangdong Kelon Air Conditioner Co., Ltd.

1 Scope and normative references

GB 14536.1 of the chapter is applicable except as follows.

1.1 Replacement.

This section applies to the use of these or equipment for use in household and similar electrical devices automatic humidity sensing controls,

It includes a controller for heating, air conditioning and similar applications. These devices can use electricity, gas, oil, solid fuel, solar energy, etc., or it

Their energy mix.

1.1.1 The following note instead of the second paragraph after the Note.

Note. in this section, "device" contains the word "appliance" and "control."

1.1.2 Replacement.

This section applies capable of reacting or humidity control Automatic electrical controls for mechanical or electronic operation.

1.1.3 Not applicable.

2 Definitions

GB 14536.1 of the chapter is applicable except as follows.

2.2 is defined by use classification controller

2.2.19 Addition.

Note. Normally, humidity sensing controls are operating controller.

increase.

2.2.101

Used to the humidity is maintained at a certain value or more, the following electric automatic controller or two specific values.

2.2.102

Used to control independently mounted or mounted living space humidity humidity sensing controls.

3 General requirements

This is applicable in GB 14536.1.

General Description 4 Test

This is applicable in GB 14536.1.

5 RATINGS

This is applicable in GB 14536.1.

Category 6

GB 14536.1 of the chapter is applicable except as follows.

6.3.9 Addition.

GB 14536.15-2008/IEC 60730-2-13.2006

6.3.9.101 --- humidity sensing controls.

6.3.9.102 --- Room humidistat.

7 Information

This is applicable in GB 14536.1.

8 Protection against electric shock

This is applicable in GB 14536.1.

9 ground protection measures

This is applicable in GB 14536.1.

10 Terminals and terminations

This is applicable in GB 14536.1.

11 structural requirements

GB 14536.1 of the chapter is applicable except as follows.

11.4.3 Addition.

NOTE. In Canada and the United States, may not be connected to the capacitor contact between the controller type 2 actions.

12 moisture and dust

This is applicable in GB 14536.1.

13 Electric strength and insulation resistance

GB 14536.1 of the chapter is applicable except as follows.

Table 13.2

Add the following note in e) is.

Note. For humidity sensing controls, the sample may need to provide specially calibrated for this test.

Fever 14

This is applicable in GB 14536.1.

15 Manufacturing deviation and drift

GB 14536.1 of the chapter is applicable except as follows.

15.1 Review.

Note 15.1 does not apply.

15.4 Addition.

Alternatively, you can use the operating value plus the tolerance value method declaration to represent the manufacturing tolerances declared and drift.

15.5.3 Addition.

15.5.3.101 expectations for self-regulation by the user controls, unless the manufacturer otherwise stated, to be set by the regulator adjustable wet

The maximum value of the range.

Operation 15.5.3.102 controller should not exceed 0.05A current sensing a sensing element to complete.

Circuit may be any convenient voltage, as long as it is possible to reliably exhibit the monitored operating condition.

GB 14536.15-2008/IEC 60730-2-13.2006

15.5.4 Not applicable.

16 Environmental Stress

This is applicable in GB 14536.1.

17 Durability

GB 14536.1 of the chapter is applicable except as follows.

17.1.3 Test procedures and conditions

increase.

17.1.3.101 moisture sensitive controller, you should start with the amount of manufacturers and testing agencies agreed to test Chapter 17.

17.8 automatic acceleration operation test

increase.

17.8.4.101 unless the manufacturer declares a higher number of cycles, automatic actions independently mounted controller and line controller with dynamic and artificial

As the number of cycles shall comply with Annex AA AA. Provisions 1.

Note. Canada and the United States applies the number of cycles, see Appendix AA, AA. Rule 2.

Test 17.16 special purpose controller

increase.

17.16.101 humidity sensing controls

--- 17.1 to 17.5 applies;

--- 17.6 applies to classified 1.Or M-2.M-type action, "X" value agreed by the manufacturer and testing body;

--- 17.7 applies;

--- 17.8 applies;

--- 17.9 applies; except.

--- 17.9.3.1 do not apply;

--- 17.10 ~ 17.14 apply.

17.16.102

NOTE. In the United States, if a controller has two or more electrical ratings (for example. inductive and resistive, or different current values at different voltages),

The controller according to a statement of not less than 25% of the number of times the durability of the number of times each test rating (if the number of durability equal to or declaration

To 30000 cycles), but the total period either on the sample than the number of times the durability of its declaration. However, at least one sample test

The total number of cycles equal to the number of times the durability of its declaration.

18 Mechanical strength

This is applicable in GB 14536.1.

19 Threaded parts and connections

This is applicable in GB 14536.1.

20 creepage distances, clearances and distances through solid insulation through

This is applicable in GB 14536.1.

21 heat, fire and tracking resistance

This is applicable in GB 14536.1.

GB 14536.15-2008/IEC 60730-2-13.2006

22 corrosion resistance

This is applicable in GB 14536.1.

23 Electromagnetic compatibility (EMC) emission requirements ---

This is applicable in GB 14536.1.

24 components

This is applicable in GB 14536.1.

25 normal operation

This is applicable in GB 14536.1.

26 Electromagnetic compatibility (EMC) requirements --- immunity

This is applicable in GB 14536.1.See Appendix H.

27 non-normal operation

This is applicable in GB 14536.1.See Appendix H.

28 Guidelines for the use of electronic disconnection

This is applicable in GB 14536.1.

GB 14536.15-2008/IEC 60730-2-13.2006

Fig GB 14536.1 FIG apply.

GB 14536.15-2008/IEC 60730-2-13.2006

appendix

GB 14536.1 Appendix, is applicable except as follows.

Appendix H

(Normative)

Requirements for electronic controllers

GB 14536.1 of the appendix, is applicable except as follows.

H. 6.18 by Software Category

H. 6.18.1 --- A class software

increase.

Note. In general, the use of software for humidity sensing controls are classified as Class A software.

H. 7 Information

Make the following changes to Table 7.2.

Information chapter, strip method

58a

increase.

Table H. 26.2.101 footnote a)

Increased requirements.

Type 2 humidity-sensitive controller output after operation

Conditions 101)

H. 26.2.103

H. 26.2.104

H. 26.2.105

101), for example, conductive or non-conductive, as applicable.

H. 11 structural requirements

H. 11.12 use the software controller

H. 11.12.8 replaced by the following sections explain.

NOTE. Table H. 7.2 The provisions of paragraph 71 values given by the applicable appliance standard.

H. 11.12.8.1 At the end of this clause to add the following explanation.

NOTE. Table H. 7.2 Section 72 applies a predetermined value by the appliance standard given.

H. 23 Electromagnetic compatibility (EMC) requirements --- immunity

H. 23.1.2 Radio frequency emissions

increase.

Integral electric load and humidity sensing controls are not subjected to this entry tests, because the results of these tests will be charged because the controller appliance

Affected, and also affected the measurement of radiation measuring device. If the manufacturer's request, the controller can also be stated in the conditions

carry out testing.

H. 26 Electromagnetic compatibility (EMC) requirements --- immunity

H. 26.2 Addition.

GB 14536.15-2008/IEC 60730-2-13.2006

After each test, shall be in accordance with Table H. One or more indicators 26.2.101 listed. 1)

1) In the original IEC as "table H.26.101", after the determination of a clerical error, the words "table H.26.2.101".

increase.

H. 26.2.101 If applicable, the controller should remain in its current state, and according to the party statement within Chapter 15 of the verification limits

Style action.

H. 26.2.102 controller shall meet the conditions shown in Table 7.2 in paragraph 101 of the statement, and should be followed as H. 26.2.101 in the normal

action.

H. 26.2.103 If you meet the controller Table 7.2 Item 101 declared conditions, should not be automatic or manual reset. Lost during normal operation

Waveform is a sine wave or meet Table 7.2 Section 53 of the declaration.

H. 26.2.104 controller remains in state Table 7.2 Item 101 declared. Non-self-resetting controller should only manually

Reset. When making operation to evacuate humidity conditions, the controller should be in accordance with H. The 26.2.101 action, or remain in H. 26.2.103 The

State declaration.

H. 26.2.105 controller may return to the initial state, and then press H. The 26.2.101 normal operation.

NOTE. If the controller in Table 7.2 under Item 101 state declaration, the controller can be reset, but when the humidity conditions so that action still exists, should again

Back to the declaration of the state.

H. 26.2.106 while the output of the controller and run the item 58a or item 58b declared in Table 7.2, the controller should meet

17.5 request.

Table H. According to the standard 26.2.101

Terms H26 test applies permissible according to the standard

Type 2 humidity sensing controls H. 26.2.101 H. 26.2.102 H. 26.2.103 H. 26.2.104 H. 26.2.105H. 26.2.106a)

H. 26.4 ~ H. 26.14 b b b a a x

Other humidity sensing controls H. 26.2.101 H. 26.2.102 H. 26.2.103 H. 26.2.104 H. 26.2.105H. 26.2.106a)

H. 26.8, H. 26.9 x x x

x = Allow; causing interference after a = action allows; the interfering action before allowing b =

a) because the output needs to determine the acceptability of the appliance, the guidelines apply only to integral or load controller.

H. 26.5 voltage sag and interruption of power supply network

H. 26.5.4 voltage fluctuation test

instead.

H. 26.5.4.3 humidity sensing controls shall be subjected to a given voltage of each test cycle three times, each test cycle interval 10s. For table

7.2 Item 101 requires the declaration of the humidity sensing controls, under the condition statement is subjected to three times per cycle, each subjected to the conditions in the non-declaration

Cycle 3 times.

H. 26.8 Surge immunity test

H. 26.8.3 Test Procedure

increase.

H. 26.8.3.101 for Table 7.2 requires the declaration of the controller Item 101, subjected to the test conditions in a statement three times in the non-declaration Article

Member under withstand twice.

GB 14536.15-2008/IEC 60730-2-13.2006

H. 26.9 Electrical fast transient/burst test

H. 26.9.3 Test Procedure

increase.

H. 26.9.3.101 controller 5 is subjected to tests. For the requirements stated in Table 7.2 Controller item 101, is applied at a position statement

3, the position of the non-declaration is applied twice.

H. 26.10 ring wave test

H. 26.10.5 Test Procedure

increase.

H. 26.10.5.101 Table 7.2 for required items declared in the controller 101, subjected to the test conditions in a statement three times in the non-declaration Article

Member under withstand twice.

H. 26.12 Radio electromagnetic field immunity

H. 26.12.2 conducted disturbances immunity

H. 26.12.2.2 Test Procedure

increase.

For the requirements stated in Table 7.2 controller Item 101, in the statement and the statement of the position of non-interference is applied respectively.

H. 26.12.3 radiated electromagnetic radiation field immunity Assessment

increase.

H. 26.12.3.101 Table 7.2 for required items declared in the controller 101, under the condition statement and statement of non-interference is applied respectively.

H. 26.13 Variation of power frequency impact test

H. 26.13.3 Test Procedure

increase.

For the requirements stated in Table 7.2 Controller item 101, under the conditions of declaration and non-declaration be tested separately.

H. 26.14 Power frequency magnetic field immunity test

H. 26.14.3 Test Procedure

increase.

For the requirements stated in Table 7.2 Controller item 101, under the conditions of declaration and non-declaration be tested separately.

H. 26.15 Conformity Assessment

H. 26.15.2 Addition.

Based on criteria in Table H. 26.2.101.

H. 26.15.4 Addition.

Based on criteria in Table H. 26.2.101.

H. 27 non-normal operation

H. 27.1.2 replace line 1 with the following.

The controller shall operate the following conditions. Also, the controller for Table 7.2 Item 101 requirements set out in the declaration and non-declaration conditions

They were tested under the conditions.

Increase in Appendix.

GB 14536.15-2008/IEC 60730-2-13.2006

Appendix AA

(Normative)

The number of cycles

AA. The number of cycles is independently mounted and with a line controller

Controller type automatic operation manual operation

Temperature sensing controls 6,000,600

Room humidistat 60,000,600

AA. The minimum number of cycles are independently mounted and with a line controller (Canada and the United States applicable)

Humidity sensing controls

A dehumidifying a humidifying

Type 1 Type 2 Type 2 Type 1

Automatic action

initial

The maximum number of cycles/min

At last

The maximum number of cycles/min

75,000

25,000

30,000

75,000

25,000

Manual operation

initial

The maximum number of cycles/min

At last

The maximum number of cycles/min

Manual work

The maximum number of cycles/min

a magnetic, manual and motor actuator switch or similar switch, and quickly closed when idle instead of gradually closed switch, on a per-minute

Clock rate of six cycles of test.

b all controllers, are (50 ± 20)% of on-time test, humidity sensing controls to a low rate of change to this test.

c does not involve the current test can be used in any convenient rate.

GB 14536.15-2008/IEC 60730-2-13.2006

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.

Referenced standards

Normative references

GB 14536.1

How to Download GB/T 14536.15-2022

1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.