GB/T 14355-2009Specification for open lifeboat (English PDF)
开敞式救生艇技术条件
This is a limited preview
Buy now to download the full PDF (11 pages)
Need quotation for your management?
Get a formal quotation for GB/T 14355-2009 in 30 minutes.
Issued by
Standardization Administration of China
Level / Type
National · Recommended
Issue date
March 9, 2009
Implementation date
November 1, 2009
Scope
GB/T 14355-2009 is the English-translated version of 开敞式救生艇技术条件.
GB/T 14355-2009 — This standard specifies the open lifeboat (hereinafter referred to as "open boat") requirements, test methods, inspection rules, marking, transportation and storage.
This standard applies to domestic sailing ship configured open lifeboat design, manufacture and acceptance.
Found what you need?
Document preview — GB/T 14355-2009
National Standard of the People's Republic of China
- ICS
- 47.020.50
- Classification
- U 27
- Replacing
- GB/T 14355-1993
Issued by: Standardization Administration of China
Contents
- Foreword
- 1 Scope
- 2 Normative references
- 3 Requirements
- 3.1 Structure and Design
Foreword
This standard replaces GB/T 14355-1993 "open lifeboat technical conditions." this standard and GB/T 14355-1993 compared with the following major changes.
--- Increased open lifeboat storage and use of environmental conditions and corrosion, sun, mildew and other requirements;
--- Provides open lifeboat hull material and internal reserve buoyancy material;
--- Complement the relevant requirements of open type lifeboat engine;
--- According to the provisions "of domestic ship navigation rules of statutory inspection techniques" (2004) The People's Republic of China Maritime Safety Administration, the test methods were Amendments and supplements, for attachment with amended;
--- Increased transportation and storage requirements.
Appendix A of this standard is an informative annex.
The standard proposed by China State Shipbuilding Corporation.
This standard by the National Standardization Technical Committee outfitting the ship lifesaving equipment Technical Committee (SAC/TC129/SC1) centralized.
This standard was drafted. Guangzhou Shipyard International Company Limited.
1 Scope
This standard specifies the open lifeboat (hereinafter referred to as "open boat") requirements, test methods, inspection rules, marking, transportation and storage.
This standard applies to domestic sailing ship configured open lifeboat design, manufacture and acceptance.
2 Normative references
The following documents contain provisions which, through reference in this standard and become the standard terms. For dated references, subsequent Amendments (not including errata content) or revisions do not apply to this standard, however, encourage the parties to the agreement are based on research Whether the latest versions of these documents. For undated reference documents, the latest versions apply to this standard.
GB/T 16167 lifeboat housing glass fiber reinforced plastic laminates Technical conditions CB/T 3767 Test Method Ship speed IMOMSC. 48 (66) resolutions of international life-saving equipment (LSA) rule
3 Requirements
3.1 Structure and Design
3.1.1 an open boat shall be capable of storing without damage at -30 °C ~ 65 °C (243K ~ 338K) temperature range; at -1 °C ~ 30 °C can normal use (272K ~ 303K) water temperature range.
3.1.2 open boats and their equipment should be able to prevent rot, corrosion-resistant, not because of the invasion of sun, sea, oil or mold and affect its normal use.
3.1.3 open boat sheer value should not average less than 4% of the captain, hull approximately parabolic arc shape.
3.1.4 an open boat should have a rigid hull and internal reserves float and set-approved ceiling. Hull structural material for the glass fiber reinforced plastic Material (referred to as "FRP") laminate, floating reserve for the closed-cell foam material.
3.1.5 an open boat cubic volume calculation method to determine Hsin, cubic capacity according to formula (1) calculated as sharp stern transom stern calculations.
Vp = L6
(2A1 + A2 + 2A3) - Vp '(1) where.
Value Vp --- boat cubic capacity, measured in cubic meters (m3);
L --- captain of value in meters (m);
--- The A1 from the cross-sectional area of \u200b\u200bthe bow value L/4 place in square meters (m2);
A2 --- boat amidships cross-sectional area values, in square meters (m2);
--- The A3 from the cross-sectional area of \u200b\u200bthe stern value L/4 place in square meters (m2);
Value Vp '--- motor boat engine and its accessories and operating premises, searchlight, life-saving communications equipment and accessories, the volume occupied by the single Bit cubic meters (m3).
A1, A2, A3 each cross-sectional area according to the formula (2).
Where.
Meters (m);
......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — 11 pages — is available in the English PDF.
Referenced standards
How to Download GB/T 14355-2009
- 1
Add to cart
Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.
- 2
Checkout
Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).
- 3
Instant delivery (0–9 sec)
Delivery is automatic: within seconds of payment you'll receive an email with a secure download link. The link stays valid for 72 hours.
- 4
Invoice included
A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.
Related Standards
GB/T 16167-2009 — Technical conditions of lifeboat glass fiber reinforced plastics laminate
GB/T 16167-2026 — Technical conditions for glass fibre reinforced plastic laminates of lifeboat hulls
GB/T 9246-2026 — Microscopes - Oculars (eyepieces)
Secure payment via Stripe
Payments accepted
GB/T 14355-2009
$195.00