GB 30734-2014Luminaires for firefighters (English PDF)

1.0 Portable II Type

0.5 Drop directions X, Y, Z Number of drops 1 per axis Nonoperating

5.3.11 Switch reliability Lamps after 50,000 switching reliability test should be kept intact, and the lamps shall be able to light up and to achieve strong, low-light switch.

5.3.12 enclosure class Luminaire enclosure rating requirements should be GB/T 4208-2008 the provisions of IP66/IP67 or IP66/IP68 of. When protection Class IP66/IP68, the manufacturer shall identify the diving depth and duration of the lamp.

5.1 General Requirements

5.1.1 lighting power supply should be used rechargeable batteries, battery replaceable lamps should be equipped with an independent battery charging cradle.

5.1.2 Lamps charger plug should be used with AC-DC converter separate structure, fixture or charger should be set to charge and discharge protection circuit.

5.1.3 explosion-proof lamps shall comply with the requirements of GB 3836.1-2010.

5.1.4 wearable lamps should have a fire helmet match fixing fittings.

5.2 Functional requirements

5.2.1 The lamps should have a strong, low-light switching function.

5.2.2 The lamps should have flashes of low-voltage alarm function.

5.3.1 Appearance and assembly

5.3.1.1 Exterior lighting should be clean, smooth, clean, non-fouling, corrosion, scratches, burrs, cracks, deformation phenomena.

5.3.1.2 Each component mounting fixtures should be complete, accurate, reliable, no defects, dislocation, loosening, switching operation should be convenient, flexible and reliable.

5.3.2 Quality Quality lamps (including battery and accessories) shall comply with the provisions of Table 2. Table 2 units of kilograms Quality category Wearable <=

0.15 Portable I type <=1.5 II type >

5.3.3 Illumination When you press the test method specified in 6.5, lighting illuminance values under steady state should be in accordance with Table 3. table 3 category Measuring distance Test beam diameter mm Illuminance lx Light low light Average Minimum Average Minimum Wearable 2 150 >=450 >=300 >=200 >=150 Portable I type 5 300 >=250 >=150 >=150 >=100 II type 10 800 >=500 >=300 >=200 >=100

5.3.4 continuous and stable working time Lamps continuous and stable working hours shall comply with the requirements of Table 4. Table 4 in min. category Continuous and stable continuous working time working time under low voltage state Low light bright light low light Wearable >=240 >=480 Portable I type >=300 >=600 Type II >=560 >=840 >=15 >=30

5.3.5 low voltage alarm time Lamps low voltage alarm time should be 10s ~ 20s.

5.3.6 continuous working time at a low voltage condition Lamps at a low voltage state of continuous working hours shall comply with the requirements of Table 4.

5.3.7 insulation At room temperature environment, the insulation resistance between the shell and the lighting live terminal shall not be less than 20MOmega, after alternating hot and humid test shall not be less than 5MOmega.

5.3.8 withstand voltage performance Lamps should be able to withstand a frequency of 50Hz ± 0.5Hz, AC voltage 500V ± 50V, which lasted withstand voltage test of the 60s ± 5s. test Inspection procedure, the lamp should surface arcing and breakdown phenomenon. After the test, the lamp shall be able to be opened and closed strong, low light switch.

5.3.9 weatherability environmental performance Lamps should be able to withstand the test specified in Table 5 climate conditions. After each test, the lamp shall be able to be on, off and Strong, low-light switch. table

5 Test Project Name Test Parameters Test Conditions Sample status Low temperature performance High temperature performance temperature -25 ± 2 duration temperature 55 ± 2 duration Light work status Alternating hot and humid performance Cold storage High-temperature storage temperature 25 ±

5.3.8 Withstand voltage characteristic sqrt

5.3.9 Weather Environmental performance Low temperature performance sqrt High temperature performance sqrt Alternating hot and humid performance sqrt Cold storage sqrt High-temperature storage sqrt

5.3.10 Resistance to mechanical Environmental performance Anti-vibration (sinusoidal) Performance sqrt Anti-drop performance sqrt 18

6.2 Function Test

6.2.1 Operation lamp switch, check the strong lamps, low-light switching function.

6.2.2 The lighting at a low voltage state, flashes through sensory inspection lamps and low voltage alarm form.

6.3 Appearance and assembly inspection Observation through the senses, touch, appearance and assembly inspection operation.

6.4 Quality Measurement With an accuracy of not less than 1g of electronic scales measuring quality lamps.

6.5 illuminance measurement After the lamp is fully charged, in the dark (no light is completely sealed space) in the open light switch, after sustained 10min, respectively, in the lamp intensity Light, low light condition, as shown in Figure 1, in front of the press table lamp test specified distance of 3, along the direction of the beam diameter, with a distributed light meter The average illuminance distribution point on the measured value of 5 predetermined beam diameter. The arithmetic mean and minimum measurements taken

5.00 as the illuminance value.

6.6 continuous and stable work time test After discharge lamps, then full power, turn on the switch, respectively, in the lamp light, low light and with the state of the timer is started, press When the method of continuously measured and recorded

6.5 illuminance values fixture until it is less than the minimum specified in Table 3 illumination or appear low voltage warning status Stop timer. The time is the time to work for a stable fixture.

6.7 Low voltage alarm time trial After discharge lamps, then full power, turn on the switch, respectively, in the lamp light, low light condition, when the lamp in the light, low light status Under low voltage alarm occurs when, with a timer is started until the lamp flashes a low voltage alarm status and stop it when disappears. This time Room lighting is low voltage alarm time. Continuous working time test at

6.8 low voltage state In 20 consecutive times charge and discharge after the lamp is fully charged, turn on the switch, respectively, in the lamp light, low light condition, when the light fixture, Low voltage alarm state low light condition disappears with the timer is started, according to the method of continuously measured and recorded

6.5 lamp illumination Value until the timer is stopped when the illumination is less than the minimum specified in Table 3 it. The next time the lamp is a low voltage state of continuous work time. Explanation. 1

--- backplane; 2

--- distributed according to meter; 3

--- lamp bracket; 6

7.3 Type inspection

7.3.1 When one of the following conditions, type of inspection should be carried out.

a) new product trial stereotypes and old products to the plant;

b) There are major changes that may affect product performance and styling product materials, design, construction, technological aspects;

c) Product Discontinuance year to resume production;

d) the occurrence of major quality accidents.

7.3.2 type test sample should be factory inspection of products at random, the number of samples of three (sets).

7.3.3 type test items and test procedures shall be in accordance with Table 7.

7.3.4 type test results of the project complies with this standard, the contractor type inspection qualified. Table

8.1.2 Charger mark sqrt sqrt sqrt

Note. "sqrt" indicates that the item be tested. 8 signs, packaging, transportation and storage

8.1.1 Lamps Flag Position should have clear and obvious lighting and lighting as one of the signs, including the following.

a) the product name;

c) protection class (class IP66/IP68, the need to label diving depth and duration);

e) date of manufacture;

f) Product Code;

g) production plant name.

8.1.2 Charger logo Location charger should be clearly evident, durable signs, including the following.

a) the product name;

c) adaptation fixture type;

d) the date of manufacture;

f) the name of the production plant.

8.1.3 Package mark It shall be printed on the box obvious, clear, durable text signs, including the following.

a) Product name, model;