Valid

GB 29201-2020National food safety standard - Food additive - Ammonia solution and liquid ammonia (English PDF)

食品安全国家标准 食品添加剂 氨水及液氨

Preview PDF

This is a limited preview

Buy now to download the full PDF

Need quotation for your management?

Get a formal quotation for GB 29201-2020 in 30 minutes.

Issued by

National Health Commission and State Administration for Market Regulation

Level / Type

National · Mandatory

Issue date

September 11, 2020

Implementation date

March 11, 2021

Scope

GB 29201-2020 is the English-translated version of 食品安全国家标准 食品添加剂 氨水及液氨.

GB 29201-2020 — This Standard applies to the food additive ammonia solution that is produced from liquid ammonia, and the food additive liquid ammonia that is produced after the liquid ammonia is purified.

Found what you need?

Document preview — GB 29201-2020

National Standard of the People's Republic of China

Issued by: National Health Commission and State Administration for Market Regulation

Contents

  • Foreword...3
  • 1 Scope...4
  • 2 Molecular formula and relative molecular mass...4
  • 3 Technical requirements...4
  • Appendix A Inspection method...6

Foreword

This Standard replaces GB 29201-2012, "National Food Safety Standard -

Food Additive - Ammonia".

Compared with GB 29201-2012, the major changes of this Standard are as

follows:

-- Change the standard name into "National food safety standard - Food

additive - Ammonia solution and liquid ammonia";

-- Add the physical and chemical indicators and inspection methods of liquid

ammonia;

-- Adopt the method that is specified in GB 5009.75 or GB 5009.12 for the

determination and inspection of lead in ammonia solution.

National food safety standard - Food additive -

Ammonia solution and liquid ammonia

1 Scope

This Standard applies to the food additive ammonia solution that is produced

from liquid ammonia, and the food additive liquid ammonia that is produced

after the liquid ammonia is purified.

2 Molecular formula and relative molecular mass

2.1 Molecular formula

Ammonia solution: NH3.H2O

Liquid ammonia: NH3

2.2 Relative molecular mass

Ammonia solution: 35.04 (according to the international relative atomic mass in

2016)

Liquid ammonia: 17.03 (according to the international relative atomic mass in

2016)

3 Technical requirements

3.1 Sensory requirements

Sensory requirements shall be in accordance with Table 1.

Table 1 -- Sensory requirements

Appendix A

Inspection method

A.1 Warning

Some reagents that are used in this test method are corrosive; the operator

must be careful! If it is splashed on the skin, use water to rinse immediately; in

severe cases, seek medical attention immediately. When flammable products

are used, it is strictly forbidden to use an open flame for heating.

A.2 General provisions

The reagents and water that are used in this Standard, when no other

requirements are specified, refer to analytical reagents and grade-III water

which is specified in GB/T 6682. The standard titration solution, the standard

solutions, preparations and products for impurity determination, which are used

in the test, are all prepared in accordance with the provisions of GB/T 601, GB/T

602, and GB/T 603, when no other requirements are specified. The used

solution, if not indicated which solvent is used, refers to aqueous solution.

A.3 Identification test

A.3.1 Reagents and materials

Hydrochloric acid.

A.3.2 Identification method

A.3.2.1 Identification of ammonia solution

Use a glass rod to dip the hydrochloric acid; close it to the sample, and there

shall be white smoke.

A.3.2.2 Identification of liquid ammonia

Take liquid ammonia samples according to the provisions of GB/T 8570.1; use

a glass rod to dip the hydrochloric acid; close it to the sample, and there shall

be white smoke.

A.4 Determination of ammonia (NH3) content

A.4.1 Method summary

Pipette an appropriate amount of sample into the sulfuric acid solution; use

sodium hydroxide standard titration solution to titrate the excess acid; use

methyl red as the indicator to determine the end point.

m1 -- sample mass, in grams (g).

The test result is based on the arithmetic mean of the parallel determination

results. The absolute difference between two independent determination results

that are obtained under repeatability conditions is not more than 0.2%.

A.5 Determination of lead (Pb)

Perform the determination according to the method that is specified in GB

5009.75 or GB 5009.12; the water that is used in the test is grade-II water that

is specified in GB/T 6682.

A.6 Determination of evaporation residue

A.6.1 Instruments and apparatuses

Electrothermal constant-temperature drying oven: Control the temperature at

105 °C +/- 2 °C.

A.6.2 Analysis steps

Use an evaporating dish that is dried to a constant mass at 105 °C +/- 2 °C; weigh

about 10 g of sample, accurate to 0.000 2 g. After it is evaporated to dryness

on a water bath, place it in the electrothermal constant-temperature drying oven,

to dry at 105 °C +/- 2 °C for 1 h; take out and cool to room temperature; weigh.

A.6.3 Result calculation

Calculate the mass fraction w2 of the evaporation residue according to Formula

(A.2):

Where:

m2 -- mass of the evaporating dish and residue after evaporation, in grams (g);

m3 -- mass of the empty evaporating dish before evaporation, in grams (g);

m4 -- sample mass, in grams (g).

The test result is based on the arithmetic mean of the parallel determination

results. The absolute difference between two independent determination results

that are obtained under repeatability conditions is not more than 0.005%.

A.7 Determination of readily oxidizable substance

A.7.1 Reagents and materials

......

......
This preview omits tables, figures, formulas and parts of the technical clauses. The complete document — all pages — is available in the English PDF.

How to Download GB 29201-2020

  1. 1

    Add to cart

    Click "Download PDF" on this page and choose "Buy this standard". You can add more standards before checkout.

  2. 2

    Checkout

    Enter your email and billing details. Payment is processed securely by Stripe (cards or bank transfer). Prefer bank details? Request a quotation (min. order $300).

  3. 3

    Fast delivery

    After payment you'll receive an email confirmation. The English PDF is sent to the same address, usually within minutes and at the latest within 1 business day.

  4. 4

    Invoice included

    A tax invoice is attached to the confirmation email. Need a custom invoice? Contact us.

Related Standards

English PDF
Fast delivery
Invoice included
View Cart

Secure payment via Stripe

Payments accepted

VisaMastercardAmerican ExpressApple PayGoogle PayStripe

GB 29201-2020

$85.00