DL/T 830-2002Technical reqirements for stoking single phase alternating current static watt-hour meter (English PDF)

1 Foreword

DL/T 830-2002 is issued by National Energy Administration.

The DL/T prefix marks a recommended standard. It is not law in itself: it becomes binding when a contract names it, when a regulation or a mandatory standard refers to it, or when a producer declares conformity with it.

The document runs to 15 pages in English translation.

2 Scope Preview

This standard specifies the mechanical and technical requirements, test and inspection rules for alternating current static watt-hour meter. This standard is applicable to manufacture, use and ordering of classes 1 and 2 installed-type single-phase static energy meters (hereinafter referred to as energy meters) for measuring AC active energy with reference frequency of 50 Hz (or 60 Hz).

DL/T 830-2002 falls under ICS 27.100, in the field of energy and heat transfer engineering.

This catalogue holds 1,145 other DL/T standards in that field.

In this catalogue, DL/T standards carry edition years from 1991 to 2026.

3 Normative references

GB/T 2423.1 — Environmental testing for electric and electronic products—Part 2: Test methods—Test A: Cold (idt IEC 60068-2-1:1990)

GB/T 2423.2 — Environmental testing for electric and electronic products—Part 2: Test methods—Test B: Dry heat (idt IEC 60068-2-2:1974)

GB/T 2423.4 — Basic environmental testing procedures for electric and electronic products—Test Db: Damp heat, cyclic (eqv IEC 60068-2-30:1980)

GB/T 2423.5 — Environmental testing for electric and electronic products—Part 2: Test methods—Test Ea and guidance: Shock (idt IEC 60068-2-27:1987)

GB/T 2423.10 — Environmental testing for electric and electronic products—Part 2: Test methods—Test Fc and guidance: Vibration (Sinusoidal) (idt IEC 60068-2-6:1982)

GB/T 2423.44 — Environmental testing for electric and electronic products—Part 2: Test methods—Test Eg: Impact, spring hammer (eqv IEC 60068-2-63:1991)

GB/T 2828 — Sampling procedures and tables for lot-by-lot inspection by attributes (Apply to inspection of successive lots or batches)

GB/T 2829 — Sampling procedures and tables for periodic inspection by attributes (Apply to inspection of stability for productive process)

GB/T 5169.10 — Fire hazard testing for electric and electronic products—Test methods—Glow-wire test methods—General (idt IEC 60695-2-1/0:1994)

GB 16910 — Elementary technological conditions of labour health for constructing small industrial enterprises

GB/T 17215 — Alternating current static watt-hour meters for active energy (classes 1 and 2) (idt IEC 61036:1996)

GB/T 17442 — Acceptance inspection for direct connected alternating current static watt-hour meters for active energy (classes 1 and 2) (idt IEC 61358:1996)

GB/T 17626.2 — Electromagnetic compatibility—Testing and measurement techniques—Electrostatic discharge immunity test (idt IEC 61000-4-2:1995)

GB/T 17626.3 — Electromagnetic compatibility—Testing and measurement techniques—Radiated radio-frequency electromagnetic field immunity test (idt IEC61000-4-3:1995)

GB/T 17626.4 — Electromagnetic compatibility—Testing and measurement techniques—Electrical fast transient/burst immunity test (idt IEC61000-4-4:1995)

GB/T 17626.5 — Electromagnetic compatibility—Testing and measurement techniques—Surge immunity test (idt IEC 61000-4-5:1995)

GB/T 17626.11 — Electromagnetic compatibility—Testing and measurement techniques—Voltage dips, short interruptions and voltage variations immunity tests (idt IEC 61000-4-11:1995)

JB/T 6214 — Guideline for reliability verification test and determination test (exponential distribution) of instruments and meters

4 About this standard

Issued by: National Energy Administration

English translation: about 15 pages (approximate)

5 Classification and status

International classification (ICS): 27.100

Chinese Standard Classification (CCS): F 2

Prefix DL/T: recommended standard.